Forums
NautiqueParts.comNautiqueSkins.com - Correct Craft Upholstery and Part
  New Posts New Posts RSS Feed - 1979 Commander 351 w/ Velvet Drive FOR SALE
  FAQ FAQ  Forum Search   Register Register  Login Login

1979 Commander 351 w/ Velvet Drive FOR SALE

 Post Reply Post Reply   
Author
nautiquefanatic View Drop Down
Gold Member
Gold Member
Avatar

Joined: April-29-2004
Location: North Carolina
Status: Offline
Points: 570
Post Options Post Options   Thanks (0) Thanks(0)   Quote nautiquefanatic Quote  Post ReplyReply Direct Link To This Post Topic: 1979 Commander 351 w/ Velvet Drive FOR SALE
    Posted: October-04-2014 at 12:25am
Motor still bolted in junk 1979 Ski Nautique. Motor is in unknown condition, missing exhaust manifolds and carb. Everything else still here....all bolt on items on front of motor, distributor, and the Velvet Drive transmission is still bolted up also. Prefer someone come pick it up. Call or text for quickest response (980)581-0006........ $500 for what is left of MOTOR and Transmission with all mounts...we will just un-bolt from stringers and lift it out. This motor and transmission has not been in the rain, has been covered with the original engine box.

Back to Top
nautiquefanatic View Drop Down
Gold Member
Gold Member
Avatar

Joined: April-29-2004
Location: North Carolina
Status: Offline
Points: 570
Post Options Post Options   Thanks (0) Thanks(0)   Quote nautiquefanatic Quote  Post ReplyReply Direct Link To This Post Posted: October-11-2014 at 12:19am
Still available......
Back to Top
nautiquefanatic View Drop Down
Gold Member
Gold Member
Avatar

Joined: April-29-2004
Location: North Carolina
Status: Offline
Points: 570
Post Options Post Options   Thanks (0) Thanks(0)   Quote nautiquefanatic Quote  Post ReplyReply Direct Link To This Post Posted: November-02-2014 at 1:57am
As of today, still here, still available.
Back to Top
CrazyCanuck View Drop Down
Senior Member
Senior Member
Avatar

Joined: July-21-2013
Location: Vancouver B.C.
Status: Offline
Points: 254
Post Options Post Options   Thanks (0) Thanks(0)   Quote CrazyCanuck Quote  Post ReplyReply Direct Link To This Post Posted: November-02-2014 at 3:35am
I'd sure like that raw water pump. I would like a spare to rebuild with new bearings....don't want to attempt it on mine and mess it up.
I also need to lengthen my drivers side exhaust pipe. Its a bit short because I have a pcm manifold on that side and it has a higher connection point than the commander log does. Two hose clamps and it still leaks a bit. Can a section be joined inline?
If only you were closer.....
https://encrypted-tbn1.gstatic.com/images?q=tbn:ANd9GcRtW3vJrMHLdqBzndt9VX3oOpBuRopGlzKq9Ea7pAO7wnTuoD8E8g
Back to Top
nautiquefanatic View Drop Down
Gold Member
Gold Member
Avatar

Joined: April-29-2004
Location: North Carolina
Status: Offline
Points: 570
Post Options Post Options   Thanks (0) Thanks(0)   Quote nautiquefanatic Quote  Post ReplyReply Direct Link To This Post Posted: December-01-2014 at 6:33pm
$450 !!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!
Back to Top
8122pbrainard View Drop Down
Grand Poobah
Grand Poobah
Avatar

Joined: September-14-2006
Location: Three Lakes Wi.
Status: Offline
Points: 41045
Post Options Post Options   Thanks (0) Thanks(0)   Quote 8122pbrainard Quote  Post ReplyReply Direct Link To This Post Posted: December-01-2014 at 8:50pm
Originally posted by CrazyCanuck CrazyCanuck wrote:

I also need to lengthen my drivers side exhaust pipe. Its a bit short because I have a pcm manifold on that side and it has a higher connection point than the commander log does. Two hose clamps and it still leaks a bit. Can a section be joined inline?

Corey,
What kind of clamps are you using? Maybe it's due to the hose being too short but, try some T bolt type clamps. Yes, the hose can be lengthened but you would need a section of tubing between the hoses. The down side to this is it doubles the potential for leaks however, good clamps and it should never leak.


54 Atom


77 Tique

64 X55 Dunphy

Keep it original, Pete
<
Back to Top
CrazyCanuck View Drop Down
Senior Member
Senior Member
Avatar

Joined: July-21-2013
Location: Vancouver B.C.
Status: Offline
Points: 254
Post Options Post Options   Thanks (0) Thanks(0)   Quote CrazyCanuck Quote  Post ReplyReply Direct Link To This Post Posted: December-01-2014 at 9:25pm
Thanks for the reply Peter.
The angle and position of the elbow on the pcm manifold is higher up, and on less of an angle than the commander one. So when the exhaust pipe was lifted up to reach, the top of the pipe does not quite stretch fully to cover the end of the pcm manifold.
It does not help that the cut on the end of the pipe at that point is a bit poor, and one bit of the reinforcement wire is peeling out at that point.
The PO used what looks like regular hose clamps, and they are tight enough to have sunk a bit into the pipe.
Since the first time I started this boat the water weeps a little bit at the top of the connection, and adding a second hose clamp has not eliminated the leak.
I thought about adding some muffler silver tape as a wrap. (cheap and cringeworthy I know)...lol

Maybe if I pull all the clamps and heat up the pipe with a heat gun, I can make an attempt to re-seat the hose better.

What clamps are best?

Thanks again.
Corey.
https://encrypted-tbn1.gstatic.com/images?q=tbn:ANd9GcRtW3vJrMHLdqBzndt9VX3oOpBuRopGlzKq9Ea7pAO7wnTuoD8E8g
Back to Top
CrazyCanuck View Drop Down
Senior Member
Senior Member
Avatar

Joined: July-21-2013
Location: Vancouver B.C.
Status: Offline
Points: 254
Post Options Post Options   Thanks (0) Thanks(0)   Quote CrazyCanuck Quote  Post ReplyReply Direct Link To This Post Posted: December-01-2014 at 9:30pm
Mr Nautiquefanatic sir, are you unwilling to part with just the raw water pump?

Let me know. I have no idea what snail mail costs from me you to me, but its worth a look if you'd sell it on its own.

Thanks.
Corey.
https://encrypted-tbn1.gstatic.com/images?q=tbn:ANd9GcRtW3vJrMHLdqBzndt9VX3oOpBuRopGlzKq9Ea7pAO7wnTuoD8E8g
Back to Top
nautiquefanatic View Drop Down
Gold Member
Gold Member
Avatar

Joined: April-29-2004
Location: North Carolina
Status: Offline
Points: 570
Post Options Post Options   Thanks (0) Thanks(0)   Quote nautiquefanatic Quote  Post ReplyReply Direct Link To This Post Posted: February-13-2015 at 12:49am
All this still for sale !!!! Call me   (980)581-0006.....will reduce price to take it all..........hull needs to go to landfill.
Back to Top
DasBoot67 View Drop Down
Groupie
Groupie


Joined: July-13-2014
Location: Danville nh
Status: Offline
Points: 74
Post Options Post Options   Thanks (0) Thanks(0)   Quote DasBoot67 Quote  Post ReplyReply Direct Link To This Post Posted: March-26-2015 at 10:00pm
That unit still available
Back to Top
nautiquefanatic View Drop Down
Gold Member
Gold Member
Avatar

Joined: April-29-2004
Location: North Carolina
Status: Offline
Points: 570
Post Options Post Options   Thanks (0) Thanks(0)   Quote nautiquefanatic Quote  Post ReplyReply Direct Link To This Post Posted: March-27-2015 at 11:45am
Originally posted by DasBoot67 DasBoot67 wrote:

That unit still available


YES DasBoot67..... It is still for sale and available. Call me (980)581-0006
Back to Top
DasBoot67 View Drop Down
Groupie
Groupie


Joined: July-13-2014
Location: Danville nh
Status: Offline
Points: 74
Post Options Post Options   Thanks (0) Thanks(0)   Quote DasBoot67 Quote  Post ReplyReply Direct Link To This Post Posted: May-14-2015 at 11:36pm
What do u what for the set up
Back to Top
larsontkmm View Drop Down
Newbie
Newbie


Joined: July-14-2005
Location: Fort Mill, SC
Status: Offline
Points: 21
Post Options Post Options   Thanks (0) Thanks(0)   Quote larsontkmm Quote  Post ReplyReply Direct Link To This Post Posted: September-30-2015 at 10:59am
Pylon still avalible?
Back to Top
 Post Reply Post Reply
  Share Topic   

Forum Jump Forum Permissions View Drop Down

Copyright 2024 | Bagley Productions, LLC