Forums
NautiqueParts.comNautiqueSkins.com - Correct Craft Upholstery and Part
  New Posts New Posts RSS Feed - MAP and Barometer Sensors on 1994 Pro Boss
  FAQ FAQ  Forum Search   Register Register  Login Login

MAP and Barometer Sensors on 1994 Pro Boss

 Post Reply Post Reply   
Author
sandro.zaal View Drop Down
Groupie
Groupie


Joined: October-08-2012
Location: Tbilisi,Georgia
Status: Offline
Points: 64
Post Options Post Options   Thanks (0) Thanks(0)   Quote sandro.zaal Quote  Post ReplyReply Direct Link To This Post Topic: MAP and Barometer Sensors on 1994 Pro Boss
    Posted: September-05-2019 at 9:27am
Hi.
There are two sensors MAP and Barometer located over each other ( MAP is lower and Barometer is upper). They both have a pipe for hose. I noticed, that only one (MAP) has a hose connected to the throttle body. Barometer is just not connected. Is it OK..? or there should be a splitter which connects these two sensors to the throttle body. Any ideas..? Thanks
Back to Top
KENO View Drop Down
Grand Poobah
Grand Poobah


Joined: June-06-2004
Location: United States
Status: Offline
Points: 11125
Post Options Post Options   Thanks (0) Thanks(0)   Quote KENO Quote  Post ReplyReply Direct Link To This Post Posted: September-05-2019 at 10:20am
Originally posted by sandro.zaal sandro.zaal wrote:

Hi.
There are two sensors MAP and Barometer located over each other ( MAP is lower and Barometer is upper). They both have a pipe for hose. I noticed, that only one (MAP) has a hose connected to the throttle body. Barometer is just not connected. Is it OK..? or there should be a splitter which connects these two sensors to the throttle body. Any ideas..? Thanks


The MAP sensor is sensing engine vacuum and the barometric sensor is sensing pressure outside the engine.

The system compares these readings to adjust operating parameters like timing and fuel flow so you don't want them connected together

The barometric sensor is OK just open to the atmosphere as it is right now, or in other words that's how it should be
Back to Top
sandro.zaal View Drop Down
Groupie
Groupie


Joined: October-08-2012
Location: Tbilisi,Georgia
Status: Offline
Points: 64
Post Options Post Options   Thanks (0) Thanks(0)   Quote sandro.zaal Quote  Post ReplyReply Direct Link To This Post Posted: September-06-2019 at 6:23am
Thanks for quick respond.
Still chasing unstable idle. Changed idle control valve recently. Same :(
Can bad MAP sensor affect on idling..?

Look at this video:

Thanks
Back to Top
gun-driver View Drop Down
Grand Poobah
Grand Poobah


Joined: July-18-2008
Location: Pittsburgh, Pa
Status: Offline
Points: 4127
Post Options Post Options   Thanks (0) Thanks(0)   Quote gun-driver Quote  Post ReplyReply Direct Link To This Post Posted: September-11-2019 at 3:26pm
Yes it could but it could also be a vacuum leak.
This shows how to do a generic test on your MAP sensor, refer to the reference section on CCF for the manual and voltages
https://axleaddict.com/auto-repair/Bad-MAP-Sensor-Symptoms-and-Testing
Back to Top
sandro.zaal View Drop Down
Groupie
Groupie


Joined: October-08-2012
Location: Tbilisi,Georgia
Status: Offline
Points: 64
Post Options Post Options   Thanks (0) Thanks(0)   Quote sandro.zaal Quote  Post ReplyReply Direct Link To This Post Posted: September-17-2019 at 11:12am
Originally posted by gun-driver gun-driver wrote:

Yes it could but it could also be a vacuum leak.
This shows how to do a generic test on your MAP sensor, refer to the reference section on CCF for the manual and voltages
https://axleaddict.com/auto-repair/Bad-MAP-Sensor-Symptoms-and-Testing


Im afraid you are right ! There is a leak between the throttle body and the engine. The massive piece of gasket is missing. Going to make a test this week.

Thanks.!
Back to Top
 Post Reply Post Reply
  Share Topic   

Forum Jump Forum Permissions View Drop Down

Copyright 2024 | Bagley Productions, LLC