Cutting out floors |
Post Reply |
Author | |
Evilsizer
Groupie Joined: August-29-2019 Location: Ohio Status: Offline Points: 62 |
Post Options
Thanks(0)
Posted: September-19-2019 at 11:10pm |
If I'm going to replace the floor since the stringers are bad do I need to grind off the floor? Or just cut them out with the glass still on them?
|
|
JoeinNY
Grand Poobah Joined: October-19-2005 Location: United States Status: Offline Points: 5693 |
Post Options
Thanks(0)
|
What boat, how much floor -
|
|
Evilsizer
Groupie Joined: August-29-2019 Location: Ohio Status: Offline Points: 62 |
Post Options
Thanks(0)
|
1978 Ski Nautique. The stringers need fixed and new foam
|
|
8122pbrainard
Grand Poobah Joined: September-14-2006 Location: Three Lakes Wi. Status: Offline Points: 41040 |
Post Options
Thanks(0)
|
Andrew,
Have you looked at any of the great stringer threads linked in the FAQ thread? Pictures too! Besides the stringer threads, lots of great info. I feel most find that a cheap diamond wheel in a right angle grinder works wonders on the glass. |
|
8122pbrainard
Grand Poobah Joined: September-14-2006 Location: Three Lakes Wi. Status: Offline Points: 41040 |
Post Options
Thanks(0)
|
BTW, many go no foam!!
|
|
Evilsizer
Groupie Joined: August-29-2019 Location: Ohio Status: Offline Points: 62 |
Post Options
Thanks(0)
|
Are the floors screwed into the stringers? Do I need to locate the screws to pull up the floors?
|
|
8122pbrainard
Grand Poobah Joined: September-14-2006 Location: Three Lakes Wi. Status: Offline Points: 41040 |
Post Options
Thanks(0)
|
You're doing stringers so just start cutting. |
|
Evilsizer
Groupie Joined: August-29-2019 Location: Ohio Status: Offline Points: 62 |
Post Options
Thanks(0)
|
Ok. So I cut a section and just pull it up? Seams like they would have screwed the floors to the stringers
|
|
JoeinNY
Grand Poobah Joined: October-19-2005 Location: United States Status: Offline Points: 5693 |
Post Options
Thanks(0)
|
If noone has messed with the boat previously it has stringers, then a few boards nailed to the top of the stringers running perpendicular to them in the back 2/3rds of the boat. In the front under the seats there are multiple boards nailed to the top of the stringers – then the whole thing was foamed. The majority of the boat the floor you see is fiberglass directly over the floor – where there was wood nailed to the stringers it is fiberglass over that wood. To replace all the stringers you would need to remove, the glass, the wood, and the foam in that order before you could cut out the stringers.
|
|
Evilsizer
Groupie Joined: August-29-2019 Location: Ohio Status: Offline Points: 62 |
Post Options
Thanks(0)
|
So the fiberglass is over the foam and no wood in between but some wood on top of the stringers
|
|
samudj01
Gold Member Joined: March-10-2009 Location: NC Status: Offline Points: 931 |
Post Options
Thanks(0)
|
Much of the floor will be ply with a layer of glass over it. In some places there may just be glass. We took an angle grinder with a cutting wheel and went all the way around the perimeter to start. Used the grinder as a guide to keep us a couple inches off the side as not to nick that glass. Then started ripping up.
|
|
78 Ski Tique, 72 Skier w/302's, 93 SN w/351 & 17 GS22 w/zr409
Previous - 99 Sport Nautique w/GT40 and 87 Martinique w/351 |
|
samudj01
Gold Member Joined: March-10-2009 Location: NC Status: Offline Points: 931 |
Post Options
Thanks(0)
|
Other than cutting through the hull you can do much wrong in taking it all out. We likes a flap disk with 36 grit for grinding.
|
|
78 Ski Tique, 72 Skier w/302's, 93 SN w/351 & 17 GS22 w/zr409
Previous - 99 Sport Nautique w/GT40 and 87 Martinique w/351 |
|
8122pbrainard
Grand Poobah Joined: September-14-2006 Location: Three Lakes Wi. Status: Offline Points: 41040 |
Post Options
Thanks(0)
|
Andrew,
Have you had a chance yet?
|
|
Post Reply | |
Tweet
|
Forum Jump | Forum Permissions You cannot post new topics in this forum You cannot reply to topics in this forum You cannot delete your posts in this forum You cannot edit your posts in this forum You cannot create polls in this forum You cannot vote in polls in this forum |