Misc parts 87 S/N, 86 Silver N |
Post Reply |
Author | |
JamoJones
Groupie Joined: September-13-2022 Location: Lee Center, NY Status: Offline Points: 50 |
Post Options
Thanks(0)
Posted: August-03-2023 at 3:40pm |
Hi All,
Looking for a few things: '87 S/N 2001...PSI dash gauge, ignition switch face/lock nut (or switch w/keys), vent grilles, any or all 3 '86 Silver Nautique 2001...bow light, stern light mount with light pole (aftermarket plastic junk now), vent grilles, one or all 3, they look to be the same as the '87, used marine distributor (I have a Jegs DUI on order, not shipped until 9/20). I'd take anything cheap just to run it, I'll even return it if you'd like when my electronic DUI comes in. Chevy 350, rotation does not matter. Thanks Guys... Jamo |
|
1986 Silver Nautique #49 of 82
1987 Ski Nautique 2001 |
|
KENO
Grand Poobah Joined: June-06-2004 Location: United States Status: Offline Points: 11112 |
Post Options
Thanks(0)
|
This may seem like a silly idea, but why not buy the alternative distributor mentioned in your other post?
This one in the link You may like it enough that you cancel the Jeg's order or you may decide to keep the DUI on order too and when it comes in you can swap it in place of the A Team and sell it or keep it and you'll have every replacement/troubleshooting part you need since all the parts from the A team distributor will work in the DUI. The advance curve is decent and it's got the same "meets USCG standards" pedigree as the DUI. Loosely translated that means that neither has been tested and certified by an independent outfit to receive USCG approval........they just say it meets the requirements. A bit of a play on words It'll get you running and then you can decide what to do If you got an old Prestolite or Mallory for example you'd need different plug wires, an external coil and a ballast resistor if it has points and the price may start adding up to about the same as the A team distributor They're both basically a clone of a GM HEI distributor that was high tech in 1976 (edit really 1974) when it was born.
|
|
Gary S
Grand Poobah Joined: November-30-2006 Location: Illinois Status: Offline Points: 14096 |
Post Options
Thanks(0)
|
And you left out the best part- It's Red!
|
|
JamoJones
Groupie Joined: September-13-2022 Location: Lee Center, NY Status: Offline Points: 50 |
Post Options
Thanks(0)
|
First of all, sorry this is in the "for sale" section. I was searching both and thought I posted in the "wanted" section.
I think you are right on the clone. I'll think about it, but it does make sense. Can one of you PooBahs move this over to Wanted for me, or should I repost. I'll eliminate the distributor foolishness. Thanks Guys...
|
|
1986 Silver Nautique #49 of 82
1987 Ski Nautique 2001 |
|
KENO
Grand Poobah Joined: June-06-2004 Location: United States Status: Offline Points: 11112 |
Post Options
Thanks(0)
|
What do you think this is Planet Nautique or something? Where everything gets put in the right place
This is CCF where you can post just about anything in any section and it never gets moved. Just doing another post in the Wanted section would be easiest
|
|
JamoJones
Groupie Joined: September-13-2022 Location: Lee Center, NY Status: Offline Points: 50 |
Post Options
Thanks(0)
|
Well isn't that disappointing. Here I thought I was on cutting edge, not bleeding edge where I usually seem to be. Ha...
I just bit on your suggestion and ordered the Chinese knock off. I have over a month to use it to decide on the other. Thanks Keno... |
|
1986 Silver Nautique #49 of 82
1987 Ski Nautique 2001 |
|
AZ86SKI
Senior Member Joined: July-05-2022 Location: Phoenix, AZ Status: Offline Points: 115 |
Post Options
Thanks(0)
|
If you are still looking for the vent grills they are available at Nautique Parts (SKU 62402). I replaced mine (86SN) and the mounting alignment holes were fairly close. A few minor adjustments but they worked out fine and looked much better new.
|
|
JamoJones
Groupie Joined: September-13-2022 Location: Lee Center, NY Status: Offline Points: 50 |
Post Options
Thanks(0)
|
Thanks AZ, appreciate the info...
|
|
1986 Silver Nautique #49 of 82
1987 Ski Nautique 2001 |
|
KENO
Grand Poobah Joined: June-06-2004 Location: United States Status: Offline Points: 11112 |
Post Options
Thanks(0)
|
Just so you know, you're not the first guy around here to put in a Chinese knock off. Here's a thread in the link below where CBR1000 dude put a Chinese Ford marine distributor from a different outfit in with good results. The "dude" never did write up a report like was asked for, but it was still running this summer with some non ignition related problems There have been others that did a homegrown conversion of an automotive one to their version pf a marine distributor And then there are those who just used an automotive one and haven't had the big boom yet anyways
|
|
JamoJones
Groupie Joined: September-13-2022 Location: Lee Center, NY Status: Offline Points: 50 |
Post Options
Thanks(0)
|
Hi Keno,
Just wanted to do a follow up on my boat. I did purchase and install the knock off from the link you provided above. We've been up north at our family camp for the last two weeks and did the repairs up there. All is good, ran almost10 flawless hours with the C-KO. I do believe I will cancel the JEGS order...
|
|
1986 Silver Nautique #49 of 82
1987 Ski Nautique 2001 |
|
ErnieJ
Newbie Joined: September-30-2023 Location: Nashville Status: Offline Points: 23 |
Post Options
Thanks(0)
|
Jamo, did you find your parts for your '86 or '87? I have an '87 S/N 2001 also and am parting it out. I have all of the pieces you mentioned for your two boats. Let me know what you may still need and I can send pics of any items needed.
|
|
ErnieJ
|
|
Matt97sport
Newbie Joined: April-22-2022 Location: 54549 Status: Offline Points: 10 |
Post Options
Thanks(0)
|
Do you have any parts for an 85 nautique 2001?
|
|
ErnieJ
Newbie Joined: September-30-2023 Location: Nashville Status: Offline Points: 23 |
Post Options
Thanks(0)
|
Matt, What do you need?
The main parts I have left are: drivers seat, gas tank, rudder and post, windshield, teak swim platform with brackets, and the observers seat base and plywood base and back with foam. no skins on the seat components
|
|
ErnieJ
|
|
Post Reply | |
Tweet
|
Forum Jump | Forum Permissions You cannot post new topics in this forum You cannot reply to topics in this forum You cannot delete your posts in this forum You cannot edit your posts in this forum You cannot create polls in this forum You cannot vote in polls in this forum |