Boats For Sale:
VelvetDrive Transmission |
Post Reply 
|
| Author | |
sam57 
Senior Member 
Joined: December-07-2007 Location: North Canton, O Status: Offline Points: 360 |
 Post Options
 Thanks(0)
 Quote Reply
 Topic: VelvetDrive TransmissionPosted: July-12-2009 at 10:11pm |
|
I had a 83 Correct Craft with a Commander 351, and a 66 Lyman with a 289 Commander. I don't know if they did any Chevrolet based engines or just Fords.
|
|
 |
|
|
Luchog
Grand Poobah 
Joined: April-17-2007 Location: Argentina Status: Offline Points: 2135 |
Post Options
Thanks(0)
Quote Reply
Posted: July-12-2009 at 10:04pm |
would that be the same "Commander" company wich did the 351s? if so they were around for some 20 years!! Any other engines they did? |
|
|
|
|
sam57
Senior Member
Joined: December-07-2007 Location: North Canton, O Status: Offline Points: 360 |
Post Options
Thanks(0)
Quote Reply
Posted: July-12-2009 at 10:01pm |
|
Eric would know!
|
|
|
|
|
clarkebar
Senior Member
Joined: January-13-2008 Location: marietta, GA Status: Offline Points: 174 |
Post Options
Thanks(0)
Quote Reply
Posted: July-12-2009 at 8:28pm |
|
I have a A1 70C was wondering if it would work with my small block. Eric stated that it would.
|
|
|
|
|
sam57
Senior Member
Joined: December-07-2007 Location: North Canton, O Status: Offline Points: 360 |
Post Options
Thanks(0)
Quote Reply
Posted: July-12-2009 at 3:36pm |
|
Eric,
Yes, the transmission is for sale. Sam |
|
|
|
|
clarkebar
Senior Member
Joined: January-13-2008 Location: marietta, GA Status: Offline Points: 174 |
Post Options
Thanks(0)
Quote Reply
Posted: July-12-2009 at 10:36am |
|
sam is the trans for sale?
Eric |
|
|
|
|
sam57
Senior Member
Joined: December-07-2007 Location: North Canton, O Status: Offline Points: 360 |
Post Options
Thanks(0)
Quote Reply
Posted: July-07-2009 at 1:56pm |
|
Dave,
I don't see why my velvet drive wouldn't work. It's made for high horsepower engines. I don't have a bell housing, but I don't think they are that hard to find. Sam |
|
|
|
|
oldboat
Newbie 
Joined: October-02-2007 Location: United States Status: Offline Points: 7 |
Post Options
Thanks(0)
Quote Reply
Posted: July-07-2009 at 11:49am |
|
Sam - I have a 57 Luger running a 400 ci Pontiac - will the velvet work on it - now using a three spd manual with a hydraulic auto clutch and I want to convert - I also need a bell housing which fits Buick/Cadillac/Oldsmobile/Pontiac - believe Chev is different. I am not that familiar with them marine drives.
I also have a 54 CorrectCraft that is on the Club site - bought new by my Dad. Thanks - Dave |
|
|
|
|
sam57
Senior Member
Joined: December-07-2007 Location: North Canton, O Status: Offline Points: 360 |
Post Options
Thanks(0)
Quote Reply
Posted: June-19-2009 at 1:19am |
|
Eric, 26 spline input shaft.
Sam |
|
|
|
|
eric lavine
Grand Poobah
Joined: August-13-2006 Location: United States Status: Offline Points: 13413 |
Post Options
Thanks(0)
Quote Reply
Posted: June-19-2009 at 12:19am |
|
will work behind a small block also, a touch longer, and 5' coupling instead of 4"
Sam 10 spline input shaft, or 26? |
|
|
"the things you own will start to own you"
|
|
|
|
|
sam57
Senior Member
Joined: December-07-2007 Location: North Canton, O Status: Offline Points: 360 |
Post Options
Thanks(0)
Quote Reply
Posted: June-18-2009 at 11:12pm |
|
VelvetDrive AS11 72C It came out of a 1966 Century with a 427 Commander with only 230 original hours. Been sitting on the shelf for 17 years, turns easy and shifts easy, and no rust. $250.
Sam |
|
|
|
|
Post Reply
|
|
Tweet
|
| Forum Jump | Forum Permissions You cannot post new topics in this forum You cannot reply to topics in this forum You cannot delete your posts in this forum You cannot edit your posts in this forum You cannot create polls in this forum You cannot vote in polls in this forum |
Topic Options
sam57 wrote: