Shaft and strut for Correct craft Martinique 1986
Printed From: CorrectCraftFan.com
Category: Repairs and Maintenance
Forum Name: Boat Maintenance
Forum Discription: Discuss maintenance of your Correct Craft
URL: http://www.CorrectCraftFan.com/forum/forum_posts.asp?TID=41341
Printed Date: April-29-2024 at 12:57am
Topic: Shaft and strut for Correct craft Martinique 1986
Posted By: dan_b16
Subject: Shaft and strut for Correct craft Martinique 1986
Date Posted: June-24-2017 at 12:02am
|
Hi everybody! I'm new on the forum....! i want replace Shaft, propeller and strut on my correct craft Martinique 1986. The old Shaft that i remove was 41" long, single taper with a 1"X4" coupler and the strut is a 6A-6.... when i look to ordered my new shaft and strut, the site recommand a 54" long shaft and a 6A-19 strut for my boat????? Somebody can tell me witch lenght of shaft and strut modèle it's suppose to fit on my boat? There is actually the wrong shaft lenght and strut on it?? Thank's 
|
Replies:
Posted By: Gary S
Date Posted: June-24-2017 at 12:26am
Somethings up- here is the list I have 1973 and up Martinique shows a 50" shaft and a 154dv strut. What is the measurement from the rear coupling on the trans to back side of the strut? ------------- http://www.correctcraftfan.com/diaries/details.asp?ID=1711&sort=&pagenum=1&yrstart=1966&yrend=1970" rel="nofollow - 69 Mustang HM SS 95 Nautique Super Sport |
Posted By: Gary S
Date Posted: June-24-2017 at 12:31am
|
Now that I look close at it though that sheet is dated 1980,they must have changed. That measurement I asked above will still help though ------------- http://www.correctcraftfan.com/diaries/details.asp?ID=1711&sort=&pagenum=1&yrstart=1966&yrend=1970" rel="nofollow - 69 Mustang HM SS 95 Nautique Super Sport |
Posted By: TRBenj
Date Posted: June-24-2017 at 12:41am
|
The 70-78 Martinique was on the ski nautique hull. From 80-84 it was the Bfn 19' hull. From 86-89 it was a larger 21' deep vee hull. Careful about sites claiming they know which years are which, lots of variation in that particular model. 6a6 and 41" shaft would be consistent with the dd Bfn (79-90), fwiw. |
Posted By: Gary S
Date Posted: June-24-2017 at 1:09am
|
There you go then,can't get an answer any better than that. ------------- http://www.correctcraftfan.com/diaries/details.asp?ID=1711&sort=&pagenum=1&yrstart=1966&yrend=1970" rel="nofollow - 69 Mustang HM SS 95 Nautique Super Sport |
Posted By: Duane in Indy
Date Posted: June-24-2017 at 7:46am
Is the existing shaft bent?? If not then it can be machined to accept a tapered coupling. Much cheaper alternative. I just finished a 41" shaft for a customer. ------------- Keep it as original as YOU want it 1978 Mustang (modified) |
dan_b16 wrote:Posted By: 8122pbrainard
Date Posted: June-24-2017 at 7:59am
|
Dan, Welcome to CCfan. Pictures of the boat would be great. Also, considering the confusion, double check the year of your Martinique. The HIN will be molded into the gel on the transom. ------------- /diaries/details.asp?ID=1622" rel="nofollow - 54 Atom /diaries/details.asp?ID=2179" rel="nofollow - 77 Tique 64 X55 Dunphy Keep it original, Pete < |
Posted By: dan_b16
Date Posted: June-24-2017 at 11:56am
|
Hi Gary The mesurement from transmission coupler til back side of the 6A6 existing strut is 36". That's why i figure out the 54" shaft connot fit here....?? It's appear not the origin shaft and strut but it's fit...?? |
Posted By: dan_b16
Date Posted: June-24-2017 at 12:33pm
|
My HIN IS : CTC01121B686 Somebody know where can i verify my hin number ( web site, etc) the year on my certificats registration is 86 but.....?? Thank's everybody I gonna upload a couple of picture soon that i can....!! |
Posted By: Gary S
Date Posted: June-24-2017 at 2:02pm
|
B686. Built in Feburary of 1986 as a 1986 model ------------- http://www.correctcraftfan.com/diaries/details.asp?ID=1711&sort=&pagenum=1&yrstart=1966&yrend=1970" rel="nofollow - 69 Mustang HM SS 95 Nautique Super Sport |
Posted By: dan_b16
Date Posted: June-24-2017 at 4:03pm
|
Hi Gary I check the list that you post and i see the martinique 21' long it's a 6A6 strut with a 1"X41" shaft..... so it's should mean that actual strut and shaft is the original size.... So if i understand my HIN, cause i see à old topic who talk about that.... CTC: correct craft 01121: serial number B : february 6: manufactured In 86 86: sale In 86 Thank's everything is better clear |
Posted By: wiscofoot
Date Posted: April-25-2019 at 1:16pm
Can I assume that this strut model number is correct for my 1976 Martinique? It has a 50" shaft. ------------- 1976 Martinique |