1970 Correct Craft Mustang Parts for Sale

Looking to part out a 1970s (year is approximate) Correct Craft Mustang. Located in Wisconsin. Buyer pays shipping.

Here are photos. Boat is located in Wisconsin. Unsure of the motor in it - can uncover for serious inquiries otherwise will not be uncovered until Spring. Based on records, appears to be a 1968.

3.7 miles.............6 minutes by car   

Please paint over the antique name on side
Not appropriate for this site.

Katie,
Thanks for the pictures. I was in town and thought I drive down into your rig shop to see if I could spot the Mustang.I couldn't but with all the snow I have a feeling it's under a big pile. It's probably best to wait till around April to get it uncovered for some interior pictures. Then you may get some better responses.

Pete, you didn't find the boat when you drove around because it was already inside getting warmed up. You should've called. :)
Below are photos. Our best bet is still that it's a 1968. The motor is a Chrysler 318. The prop and the rudder have the tiniest nicks in them, which are shown in the photos. Both would be easily repairable.
PM me for inquiries on a specific part. Buyer pays shipping.
List of available parts. Message me with questions about additional parts.
1. blower and bilge dash hardware
2. engine carb
3. correct craft emblem port
4. correct craft emblem stbd
5. dash panel (without gauges - will also sell whole w/ gauges)
6. driver's seat
7. engine manifolds
8. forward vent - port and stbd
9. front nav light
10. fuel fill
11. fuel window
12. fuel tank
13. gauges - engine temp, tach, oil pressure, voltage, fuel
14. gunnel step pads
15. intake strainer
16. motor box
17. mustang decal
18. nav light button
19. observer's seat
20. exhausts - port and stbd
21. prop
22. rear seat - back and bottom
23. rear vents - port and stbd
24. rope cleats
25. rope guard
26. rudder
27. rudder port
28. rudder arm
29. shaft
30. ski pylon
31. speedo pickup
32. steering wheel - not original
33. stern light w/ flag
34. shaft strut
35. throttle
36. transmission
37. transom lifting ring
38. stern light hardware
39. windshield - dual pane assembly.

Ok very cool klamon
Zwoobah wanted some stuff
Wish I lived closure

Evening everyone. Private messages sent to everyone who have expressed interest in parts.
PM me with offers or inquiries on parts - quite a few serious inquiries coming in on FB as well so doesn’t look like the parts will stick around for long.
Have a good night.

Motor is a Chrysler 318. 1968. Unknown issues at this time. The starter engages but motor didn’t turn over today when we turned the key. Due to costs and return on investment, we are not planning on delving much farther into the motor. All parts are being sold as is.

klamon wrote: Motor is a Chrysler 318. 1968.

Katie,
Many of the Mustangs did come through with the 318's but also many had the 273's. Per your grandfather in law, the thought was that Ralph always felt the 318's were just a little too much engine for the small hull. If you haven't already looked and if still it's there, the ID tag will confirm the displacement and rotation.



Both engines will look the same.

Correct, TRBenj. None of the tags are visible any more so we looked on the casting to get the 318 and 1968 data.
Have a great day.

Good morning,

The step pads in their entirety have been sold. Are there other trim pieces you may want off this boat?

By generic I assume you mean “off the shelf” as opposed to Cc-specific, which I believe is true. That said, none of the frames in the link you posted match the original style.

Not that simple as the inside dimensions may match the rubber pad but will not match the style, which is curved.



Despite being “generic”, the frames are rarely found listed for sale (used). No new ones currently on the market match. More than the LxWxD dimensions would be needed to recreate them.

How much for windshield, correct craft metal logos and mustang logo?