Boats For Sale:
my new boat couple ? |
Post Reply 
|
| Author | |
captan1 
Senior Member 
Joined: June-02-2004 Location: United States Status: Offline Points: 180 |
 Post Options
 Thanks(0)
 Quote Reply
 Topic: my new boat couple ?Posted: May-18-2005 at 11:33pm |
|
glen-l.com, the boat kit people is where I picked up the carb wedge...
|
|
 |
|
|
Siveck
Senior Member
Joined: March-14-2005 Location: Birmingham, AL Status: Offline Points: 100 |
Post Options
Thanks(0)
Quote Reply
Posted: May-16-2005 at 5:09pm |
|
I would highly reccomend an HEI distributor from performancedistributors.com. It is a bit pricey, but it will save some headaches now and in the future. It has a simple two wire hookup and no need for all that spagetti wiring and ballast resistor. The advance curve seems to be much smoother than with the factory Mallory distributor. I should have bought this in the beginning instead of wasting my time and money on the original setup. I'm very pleased with the HEI unit.
Your motor is most likely a reverse roation motor. If you are looking at the crank pulley, the reverse rotation motor will spin counterclockwise as it turns (bump the starter to verify if not running yet). |
|
|
1975 Ski Nautique
"Small Letter Boat" |
|
|
|
|
Morfoot
Grand Poobah 
Joined: February-06-2004 Location: South Lanier Status: Offline Points: 5320 |
Post Options
Thanks(0)
Quote Reply
Posted: May-16-2005 at 9:14am |
|
Welcome to our little correct craft information hideaway. If you look on past post on this website you find alot of discussion about EI's. I myself postd several discussions about the pertronix type installed on my boat. 882001 gave you a great site to start as that is where I got mine from. Helpful guys and highly recommend them. I know through reading several posts on this siot that the guys at skidim are very helpful too. Let us know if you need help and we all will try to help if we can.Lot of boat knowledge in here and we all learn from past experiences from one another as well as do's and dont's. AGAIN welcome new CC member.
|
|
|
"Morfoot; He can ski. He can wakeboard.He can cook chicken.He can create his own self-named beverage, & can also apparently fly. A man of many talents."72 Mustang "Kermit",88 SN Miss Scarlett, 99 SN "Sherman"
|
|
|
|
|
fordtech480
Newbie 
Joined: May-15-2005 Location: Andorra Status: Offline Points: 8 |
Post Options
Thanks(0)
Quote Reply
Posted: May-16-2005 at 4:05am |
|
Thanks maybe i'll try running it with out it first
|
|
|
|
|
882001
Senior Member
Joined: October-21-2003 Location: United States Status: Offline Points: 332 |
Post Options
Thanks(0)
Quote Reply
Posted: May-15-2005 at 2:49pm |
|
www.vintageperformance.com for the ect ign.
my boat doesnt have the angled plate and it runs great so i dont know if you will gain anything but skidim has them let us know if it helps anything. |
|
|
kemah texas
1988 skinautique "2001" |
|
|
|
|
fordtech480
Newbie
Joined: May-15-2005 Location: Andorra Status: Offline Points: 8 |
Post Options
Thanks(0)
Quote Reply
Posted: May-15-2005 at 2:30pm |
|
Hello everyone new to the forum. I just bought a 75' nautique. It has not been run in 6 years. I have a couple questions. how do I find out what motor i have i know it's a 351. I need to know rotation of the engine. also does anyone make a coversion kit to electronic ign. i want to get rid of the points. I may go with a msd setup. just wondering. also i am looking for the angle plate that mounts under the carb. if anyone has one or know where to get one it would be a big help. thanks todd
|
|
|
|
|
Post Reply
|
|
Tweet
|
| Forum Jump | Forum Permissions You cannot post new topics in this forum You cannot reply to topics in this forum You cannot delete your posts in this forum You cannot edit your posts in this forum You cannot create polls in this forum You cannot vote in polls in this forum |
Topic Options