transmission fluid level

Message Topic Search Topic Options Post Reply Create New Topic Printable Version Translate Topic

   Ron - I think you are fine with 2 quarts.   I cannot read my oil level either - the ATF wets out on the dispstick plating so much I can't really read it.   I ended up with an extra quart in the tranny - I thought I had emptied it & refilled per spec, but apparently was not really empty.   Point is, there was no adverse consequence - no blown seals.

Author	Message Topic Search Topic Options Post Reply Create New Topic Printable Version Translate Topic
SNobsessed Members Profile Send Private Message Find Members Posts Add to Buddy List Grand Poobah Joined: October-21-2007 Location: IA Status: Offline Points: 7102	Post Options Post Reply Quote SNobsessed Report Post Thanks(0) Quote Reply Topic: transmission fluid level Posted: September-16-2010 at 10:57am
	Ron - I think you are fine with 2 quarts. I cannot read my oil level either - the ATF wets out on the dispstick plating so much I can't really read it. I ended up with an extra quart in the tranny - I thought I had emptied it & refilled per spec, but apparently was not really empty. Point is, there was no adverse consequence - no blown seals.
	“Beer is proof that God loves us and wants us to be happy.” Ben Franklin

aquaman766 Members Profile Send Private Message Find Members Posts Add to Buddy List Newbie Joined: May-02-2010 Location: Gasport, N.Y. Status: Offline Points: 20	Post Options Post Reply Quote aquaman766 Report Post Thanks(0) Quote Reply Posted: September-16-2010 at 2:24am
	After reading the instructions again i followed step 5 on page 39 which says to fill it to the top mark when cold. However when its checked hot it is well past the mark. I guess its better to have too much than not enough. I've got a little over 2 qts in it. I still don't know why i don't have a flat spot on my dipstick? Page 37 says all transmissions after 7/15/1990 have a flat spot. oh well, thank you for the help.

8122pbrainard Members Profile Send Private Message Find Members Posts Add to Buddy List Grand Poobah Joined: September-14-2006 Location: Three Lakes Wi. Status: Offline Points: 41045	Post Options Post Reply Quote 8122pbrainard Report Post Thanks(0) Quote Reply Posted: September-15-2010 at 9:10pm
	Ron, The manual in the ref section states to just rest the dipstick on the top of the case. Cold, I'd say it would be the bottom mark since trans fluid expands when it gets hot. Take another look at the instructions in the on site manual.
	54 Atom 77 Tique 64 X55 Dunphy Keep it original, Pete <

aquaman766 Members Profile Send Private Message Find Members Posts Add to Buddy List Newbie Joined: May-02-2010 Location: Gasport, N.Y. Status: Offline Points: 20	Post Options Post Reply Quote aquaman766 Report Post Thanks(0) Quote Reply Posted: September-15-2010 at 8:48pm
	Thanks guys, My owners manual is slightly different and covers several models. I have a couple more questions. Step 4 says to set the dipstick in position. Does that mean all the way in or just to the first o-ring? When checking the fluid cold it says the oil should be to the full mark. I'm i guessing thats the top mark? The reason i'm not sure is that it would be at the same mark when checked hot or cold acording to the instructions. I have the dipstick that is at the bottom of the three that are pictured. When cold, the oil is at the top mark as these instructions recommend. However, when its hot the oil is above the top mark. I hope i don't have too much in it. I think i could have a good career at writting instructions and manuals. I'm sure i could make it more clear than the guys who wrote this one. I thought i was stupid but my girlfriend is a teacher and she was baffled as well.

sagres88 Members Profile Send Private Message Find Members Posts Add to Buddy List Newbie Joined: May-28-2010 Location: Netherlands Status: Offline Points: 19	Post Options Post Reply Quote sagres88 Report Post Thanks(0) Quote Reply Posted: September-15-2010 at 4:39pm
	Ron, Here is the page from the manual. And it is very specific on how to do it.
	1990 Ski Nautique

8122pbrainard Members Profile Send Private Message Find Members Posts Add to Buddy List Grand Poobah Joined: September-14-2006 Location: Three Lakes Wi. Status: Offline Points: 41045	Post Options Post Reply Quote 8122pbrainard Report Post Thanks(0) Quote Reply Posted: September-14-2010 at 11:28pm
	Ron, Take a look in the reference section under manuals. At the very bottom is the PCM 1993 manual. I just looked at it under the part that covers checking the fluid level. It's very specific on how to do it. What "manual" are you using????
	54 Atom 77 Tique 64 X55 Dunphy Keep it original, Pete <

aquaman766 Members Profile Send Private Message Find Members Posts Add to Buddy List Newbie Joined: May-02-2010 Location: Gasport, N.Y. Status: Offline Points: 20	Post Options Post Reply Quote aquaman766 Report Post Thanks(0) Quote Reply Posted: September-14-2010 at 10:39pm
	I have a 1993 pcm 1.23/1 trans. My owners manual is useless, it says that the dip stick has a flat side. It does'nt! How do i check the fluid? The dipstick has 2 O-rings at the top and 2 lines on it. Do i check it hot or cold? Do i put the stick in to the first o-ring or do i put it all the way in? Where should the fluid be on the stick, at the 1st or 2nd line? I have asked 2 people and i've gotten 2 different answers. I just got the boat this year so i hope you will excuse my ignorance.

transmission fluid level

About CCF

Donate

Partners

Contact