Boats For Sale:
leveling for stringers |
Post Reply 
|
| Author | |
bbishop1974 
Senior Member 
Joined: May-16-2010 Location: rindge,nh Status: Offline Points: 275 |
 Post Options
 Thanks(0)
 Quote Reply
 Topic: leveling for stringersPosted: November-11-2011 at 11:06pm |
|
secondary out,seems like a little drying overnight helped.primary glass to floor.letting it dry a couple days to see if it helps.
|
|
 |
|
|
charger496
Senior Member
Joined: August-06-2010 Location: atlanta, ga Status: Offline Points: 157 |
Post Options
Thanks(0)
Quote Reply
Posted: November-11-2011 at 12:18pm |
|
Try a sawsall with a long blade. Just be careful not to cut through the hull.
|
|
|
|
|
bbishop1974
Senior Member
Joined: May-16-2010 Location: rindge,nh Status: Offline Points: 275 |
Post Options
Thanks(0)
Quote Reply
Posted: November-09-2011 at 2:40pm |
|
thanks greg,been doing my reading/note taking.have all the gear/tools.just amazingly solid at the hull.very little rot at tops of wood.mostly just discoloration.wood very wet though.i did just walk away.wood is starting to crack and i want a good template.i have cut glass down to hull as low as possible.trying to be patient
|
|
|
|
|
BuffaloBFN
Grand Poobah 
Joined: June-24-2007 Location: Gainesville,GA Status: Offline Points: 6094 |
Post Options
Thanks(0)
Quote Reply
Posted: November-09-2011 at 9:48am |
If you're anything like me, it's best to walk away when that face appears. 
Don't forget your tyvek suit and respirator. |
|
|
|
|
BuffaloBFN
Grand Poobah
Joined: June-24-2007 Location: Gainesville,GA Status: Offline Points: 6094 |
Post Options
Thanks(0)
Quote Reply
Posted: November-09-2011 at 9:46am |
|
A grinder with a metal disk(composite) or a diamond disk works great for cutting right at the seam. If you have air tools, you can keep the 'dust' to a minimum with a little water.
|
|
|
|
|
bbishop1974
Senior Member
Joined: May-16-2010 Location: rindge,nh Status: Offline Points: 275 |
Post Options
Thanks(0)
Quote Reply
Posted: November-08-2011 at 6:43pm |
|
yes,approx 1/4 inch higher on drivers side front to back.i decided to start tearing apart with stringers level.let the motor mounts compensate.man,these stringers suck to get out.trying to take out drivers side secondary,wood is in very good condition at hull and does not want to give up.
|
|
|
|
|
BuffaloBFN
Grand Poobah
Joined: June-24-2007 Location: Gainesville,GA Status: Offline Points: 6094 |
Post Options
Thanks(0)
Quote Reply
Posted: November-08-2011 at 11:31am |
|
Not to worry Brian; most times it's me being slow. Tim got it.
Is the 1/4" out on the same side? |
|
|
|
|
bbishop1974
Senior Member
Joined: May-16-2010 Location: rindge,nh Status: Offline Points: 275 |
Post Options
Thanks(0)
Quote Reply
Posted: November-07-2011 at 10:33pm |
|
sorry my question sounds confusing.reading it i was thinking i sound like a dumba$$.i estimate it to be off 1/4 in.maybe more measuring across at the deck front and rear.measuring at stringers iam perfect.measurments done with 4 ft level.thanks for responding.
|
|
|
|
|
BuffaloBFN
Grand Poobah
Joined: June-24-2007 Location: Gainesville,GA Status: Offline Points: 6094 |
Post Options
Thanks(0)
Quote Reply
Posted: November-07-2011 at 4:05pm |
|
I agree with Tim. If the mains are level fore to aft and side to side, one has a standard to work back to. I'm not entirely sure I follow level at deck and dash.
|
|
|
|
|
TRBenj
Grand Poobah
Joined: June-29-2005 Location: NWCT Status: Offline Points: 21186 |
Post Options
Thanks(0)
Quote Reply
Posted: November-07-2011 at 11:55am |
|
If youre level at the stringers but not at the deck, sounds like one or the other was installed crooked? Id be inclined to try and figure out which was correct, unless its only off a little bit. The goal is to get the boat level to a point where you can verify that your new parts (stringers) are level as you assemble the boat back together. If youre off a little, its not a huge deal, as the motor mounts will absorb a decent amount of variation.
|
|
|
|
|
bbishop1974
Senior Member
Joined: May-16-2010 Location: rindge,nh Status: Offline Points: 275 |
Post Options
Thanks(0)
Quote Reply
Posted: November-06-2011 at 11:12pm |
|
need some advise,leveled the 86' for stringer job.it is set up now so it is level side to side across all stringers front to back.it is supported below windshield frame,keel below windshield and rear corners.my concearn is it is not level at the deck in rear or dash.would you guys keep it set up the same or level the whole boat?
|
|
|
|
|
Post Reply
|
|
Tweet
|
| Forum Jump | Forum Permissions You cannot post new topics in this forum You cannot reply to topics in this forum You cannot delete your posts in this forum You cannot edit your posts in this forum You cannot create polls in this forum You cannot vote in polls in this forum |
Topic Options
bbishop1974 wrote: