Boats For Sale:
Replace exhaust tubes while in water? |
Post Reply 
|
| Author | |
storm34 
Grand Poobah 
Joined: November-03-2008 Location: Dexter Iowa Status: Offline Points: 4492 |
 Post Options
 Thanks(0)
 Quote Reply
 Topic: Replace exhaust tubes while in water?Posted: July-17-2013 at 3:32pm |
|
The safest route would be to use a 4" rubber plumbing end cap on the exhaust tip. This way you can pull the entire thing off and have no worries with water intrusion or something giving way.
End caps |
|
 |
|
|
Bakchose
Gold Member 
Joined: November-04-2004 Location: Boston, MA Status: Offline Points: 554 |
Post Options
Thanks(0)
Quote Reply
Posted: July-17-2013 at 3:17pm |
|
That was on the 65 mustang.
|
|
|
|
|
Bakchose
Gold Member
Joined: November-04-2004 Location: Boston, MA Status: Offline Points: 554 |
Post Options
Thanks(0)
Quote Reply
Posted: July-17-2013 at 3:15pm |
|
I had mine rot and break while I was out on the lake. I had to beach the boatto keep it from sinking. What used was a tupperwear cup from the seventies. Hammered in the exhaust tip, replaced it, and then took vice grips to pull it out the cup. It worked great.
|
|
|
|
|
ArtCozier
Platinum Member
Joined: April-25-2012 Location: Orlando FL Status: Offline Points: 1023 |
Post Options
Thanks(0)
Quote Reply
Posted: July-17-2013 at 2:34pm |
|
You might have to rebuild the round hose connector on the mufflers. Easy job if you are handy with fiberglass. Take the muffler(s) out of the boat. Just make sure you don't get it oversize.
Art |
|
|
"Art"
|
|
|
|
|
mark c
Gold Member
Joined: May-09-2012 Location: Massachusetts Status: Offline Points: 534 |
Post Options
Thanks(0)
Quote Reply
Posted: July-17-2013 at 2:11pm |
|
3" expandable pipe plug, $8.40 at Grainger. Remove your flapper, install inside the exhaust pipe fitting through the transom and tighten. You coould completely remove the exhaust all the way from the transom to the risers and not get any water in the boat (test it for a tight water proof fit first). Of course if you can get it out of the water, it won't have to cost you anything, and it might be tough to come by in Sweden.
  Has a reach of 2.8 to 3.1". They also make 4" plugs for $9.27 each. Either is rated at 40 feet of head. |
|
|
|
|
turningpoint84
Platinum Member
Joined: September-11-2008 Location: Cincinnati, OH Status: Offline Points: 1467 |
Post Options
Thanks(0)
Quote Reply
Posted: July-17-2013 at 1:40pm |
|
Ha, my company could actually make something like this, we have the capabilities, but I don't think they'd be too happy.
|
|
|
Proud 1968 mustang owner and now
1970 Mustang |
|
|
|
|
Bri892001
Grand Poobah
Joined: September-27-2008 Location: Boston MA Status: Offline Points: 4947 |
Post Options
Thanks(0)
Quote Reply
Posted: July-17-2013 at 1:17pm |
|
The same thoughts have occurred to me when looking at replacing cooling hoses.
I've replaced an impeller with the boat in the water, and also cleared the tranny cooler of debri that way. But certain hoses are below the water line, so you have to be careful. It had occurred to me to shove a nerf football or something into the exhaust outlet for your procedure. But, you'd want to have a helper back there, making sure it didn't come loose. Probably not worth the risk unless it is a real hassle to pull the boat out of the water. |
|
|
|
|
JophWeud
Newbie 
Joined: August-18-2012 Location: Sweden Status: Offline Points: 31 |
Post Options
Thanks(0)
Quote Reply
Posted: July-17-2013 at 1:00pm |
|
Funny!
You have to understand that I'm new on this boats:-) |
|
|
|
|
Bri892001
Grand Poobah
Joined: September-27-2008 Location: Boston MA Status: Offline Points: 4947 |
Post Options
Thanks(0)
Quote Reply
Posted: July-17-2013 at 12:09pm |
|
You could buy a surgical Balloon Angioplasty balloon... but a very, very large one. And, Insert it into the stern end of your exhaust, then inflate it to stop the inward flow of water... while you operate on the tubes
 Just kidding of course, that image came to mind for some reason. 
|
|
|
|
|
JophWeud
Newbie
Joined: August-18-2012 Location: Sweden Status: Offline Points: 31 |
Post Options
Thanks(0)
Quote Reply
Posted: July-17-2013 at 9:02am |
|
Thanks, I wouldn't be a foolhardy, have had enough unlucky leakage this year. Sinking it would be the last I would risk!
I have a trailer, but rather steep where the ramp is, but I will take her up, thanks for advice! |
|
|
--I will never be a grown up....almost 40--
|
|
|
|
|
SNobsessed
Grand Poobah
Joined: October-21-2007 Location: IA Status: Offline Points: 7102 |
Post Options
Thanks(1)
Quote Reply
Posted: July-17-2013 at 8:54am |
|
Possible yes, but foolhardy. A high risk of sinking. Do you have a trailer available? or a neighbor with a lift you can borrow?
|
|
|
“Beer is proof that God loves us and wants us to be happy.”
Ben Franklin |
|
|
|
|
JophWeud
Newbie
Joined: August-18-2012 Location: Sweden Status: Offline Points: 31 |
Post Options
Thanks(0)
Quote Reply
Posted: July-17-2013 at 7:55am |
|
Hi, have noticed that both the exhaust tubes( between the engine and the low located muffler) have started to leak.
Have tried to tighten the rubber hoses, but the exhaust tubes of fiberglass seems to be cracked at the edges where they are connected to the rubber hoses( tigthend to hard..., or just old). Now the question: Is it possible to replace the tubes while the boat is in water, or does it has to be on trailer/land? |
|
|
--I will never be a grown up....almost 40--
|
|
|
|
|
Post Reply
|
|
Tweet
|
| Forum Jump | Forum Permissions You cannot post new topics in this forum You cannot reply to topics in this forum You cannot delete your posts in this forum You cannot edit your posts in this forum You cannot create polls in this forum You cannot vote in polls in this forum |
Topic Options