Boats For Sale:
Cutless Bearing |
Post Reply 
|
| Author | |
JPASS 
Grand Poobah 
Joined: June-17-2013 Location: Orlando Status: Offline Points: 2283 |
 Post Options
 Thanks(0)
 Quote Reply
 Topic: Cutless BearingPosted: March-28-2014 at 10:03pm |
|
|
|
|
'92 Correctcraft Ski Nautique
|
|
 |
|
|
DrCC
Grand Poobah
Joined: April-12-2004 Location: at home Status: Offline Points: 2867 |
Post Options
Thanks(0)
Quote Reply
Posted: March-28-2014 at 9:55pm |
|
And, If you don't have access to a hydraulic press. At least try a deep well socket and a 2.5 lb hammer before you get out the saws.
I've had several successful removals with the hammer/socket method. And the cutlass in the freezer trick is truly magical. |
|
|
|
|
DrCC
Grand Poobah
Joined: April-12-2004 Location: at home Status: Offline Points: 2867 |
Post Options
Thanks(0)
Quote Reply
Posted: March-28-2014 at 9:38pm |
|
The cut and curl method was always the last resort for the few that would not press out
|
|
|
|
|
8122pbrainard
Grand Poobah
Joined: September-14-2006 Location: Three Lakes Wi. Status: Offline Points: 41045 |
Post Options
Thanks(0)
Quote Reply
Posted: March-28-2014 at 9:22pm |
Arm flex!! 
|
|
|
|
|
MrMcD
Grand Poobah
Joined: January-28-2014 Location: Folsom, CA Status: Offline Points: 3749 |
Post Options
Thanks(0)
Quote Reply
Posted: March-28-2014 at 1:02pm |
|
I agree with be prepared for a long battle. It took well over an hour for me. Just did my 95 two months back. Cutting the old cutlass and not cutting your strut takes patience and time. I did the hack saw route, if I did it again I may go buy brand new 10 inch blades for my sawsall with small metal cutting teeth and use it. Cutting with my hack saw it was difficult, the blade seemed to cut the ends more than the middle, blade flex maybe? I think the sawsall might make short work of the cut. I also cut in three places, it helped peel the old one out. They do not want to be removed.
|
|
|
|
|
TX Foilhead
Grand Poobah
Joined: February-01-2009 Location: Kingsland TX Status: Offline Points: 2076 |
Post Options
Thanks(0)
Quote Reply
Posted: March-28-2014 at 2:18am |
|
Cut it with the sawzall and be prepared for a long battle. Did mine last year and It took at least an hour to get it out, it's not really easy to get it to start to curl and it's in a family uncomfortable spot to work. I went with the plastic ones for the replacement and they were pretty easy to put it and everything runs so much smoother now.
|
|
|
|
|
captbob626
Senior Member 
Joined: September-12-2013 Location: Cape MAy,NJ Status: Offline Points: 203 |
Post Options
Thanks(0)
Quote Reply
Posted: March-28-2014 at 1:20am |
|
Put the bearing in the freezer overnight and it will slip right in. Do it quickly. Doesn't hurt to heat the strut a little with a little heat before lipping bearing in.
|
|
|
Bob Meimbresse
|
|
|
|
|
SNobsessed
Grand Poobah
Joined: October-21-2007 Location: IA Status: Offline Points: 7102 |
Post Options
Thanks(0)
Quote Reply
Posted: March-27-2014 at 4:36pm |
|
Shaft must be removed to replace cutlass bearing - unless you want to remove strut, which is even more work.
There is another thread going on right now regarding where to buy. A good way to remove is to saw from inside out with a hacksaw blade mounted upside down. The curl the cut end with a punch & grab it with pliers. Installation can be done with threaded rod to act as a puller. There have been several threads with pictures on this, so you may want to search via Google. Good luck! |
|
|
“Beer is proof that God loves us and wants us to be happy.”
Ben Franklin |
|
|
|
|
jcottle
Newbie 
Joined: April-19-2009 Location: Andalusia,AL Status: Offline Points: 6 |
Post Options
Thanks(0)
Quote Reply
Posted: March-27-2014 at 2:36pm |
|
I'm replacing the cutless bearing in my 88 SN. It's a 1' OD shaft with a 1-1/4' ID strut.Is there a stock replacement for this application and where is the best place to purchase one. Also any advice on how to "DIY" removal/install without removing the shaft.I'm trying to avoid the cost of buying an expensive puller set.
|
|
|
|
|
Post Reply
|
|
Tweet
|
| Forum Jump | Forum Permissions You cannot post new topics in this forum You cannot reply to topics in this forum You cannot delete your posts in this forum You cannot edit your posts in this forum You cannot create polls in this forum You cannot vote in polls in this forum |
Topic Options
MrMcD wrote: