Boats For Sale:
Rub Rail Attachment on 85 |
Post Reply 
|
| Author | |
captbob626 
Senior Member 
Joined: September-12-2013 Location: Cape MAy,NJ Status: Offline Points: 203 |
 Post Options
 Thanks(0)
 Quote Reply
 Topic: Rub Rail Attachment on 85Posted: May-05-2015 at 9:00pm |
|
I bought # 8 1 1/4" truss head scores from Jamestown dist. Work well without spreading rub rail.
|
|
|
Bob Meimbresse
|
|
 |
|
|
8122pbrainard
Grand Poobah 
Joined: September-14-2006 Location: Three Lakes Wi. Status: Offline Points: 41045 |
Post Options
Thanks(0)
Quote Reply
Posted: April-30-2015 at 12:18am |
|
Paul,
I too use syringes. Good old McMaster has them in a variety of sizes. Cheap and I think they comes in bags of 20. Let the epoxy cure and you can pull the left over slug out and use it again/ |
|
|
|
|
gun-driver
Grand Poobah
Joined: July-18-2008 Location: Pittsburgh, Pa Status: Offline Points: 4127 |
Post Options
Thanks(0)
Quote Reply
Posted: April-29-2015 at 10:49pm |
|
That's a good idea Pete I used a big syringe that they sell in the horse dept of my local tractor supply.
|
|
|
|
|
8122pbrainard
Grand Poobah
Joined: September-14-2006 Location: Three Lakes Wi. Status: Offline Points: 41045 |
Post Options
Thanks(0)
Quote Reply
Posted: April-29-2015 at 8:28pm |
|
Chuck,
The danger of caulking is running into a old hole with the new install. Fill then as recommended with thickened epoxy. If you like the idea of a caulking gun, they do have empties. Fill one up with the epoxy mix and go for it! |
|
|
|
|
chuckactor
Senior Member
Joined: August-20-2013 Location: Ft Collins CO Status: Offline Points: 102 |
Post Options
Thanks(0)
Quote Reply
Posted: April-29-2015 at 6:03pm |
|
Wow! I hope mine ends up half as nice. Mine is grey hull with Burgundy stripes. Mine was so faded I couldn't even tell the shadow on the letters was red originally. Do you think it would be OK caulking the old holes... As you know, there are a ton of them.
Chuck |
|
|
|
|
gun-driver
Grand Poobah
Joined: July-18-2008 Location: Pittsburgh, Pa Status: Offline Points: 4127 |
Post Options
Thanks(0)
Quote Reply
Posted: April-29-2015 at 3:21pm |
|
Should I use the same type of screws to install the new one? Yes
Would it be better to use a pan head type screw No I assume I need to pilot drill each hole Yes to avoid ripples in the rub-rail during install... Do it in the sun on a hot day then give it a (TINY) bit of strech. The trick is to not over tighten the screw which buldges the rubber. I filled all the old holes with thickened epoxy before installing the new one.   
|
|
|
|
|
chuckactor
Senior Member
Joined: August-20-2013 Location: Ft Collins CO Status: Offline Points: 102 |
Post Options
Thanks(0)
Quote Reply
Posted: April-29-2015 at 1:09pm |
|
I have my '85 2001 stripped down and being sanded and buffed out. I went ahead and removed the rub rail and purchased a new one. The original was held on by a ton of what looks like 1" #8 flat head screws. Should I use the same type of screws to install the new one? Would it be better to use a pan head type screw to avoid ripples in the rub-rail during install?
Also, I assume I need to pilot drill each hole. Should I leave the hole in the rub rail slightly bigger than the screw? Thanks! Chuck |
|
|
|
|
Post Reply
|
|
Tweet
|
| Forum Jump | Forum Permissions You cannot post new topics in this forum You cannot reply to topics in this forum You cannot delete your posts in this forum You cannot edit your posts in this forum You cannot create polls in this forum You cannot vote in polls in this forum |
Topic Options