Boats For Sale:
Frozen distributor |
Post Reply 
|
| Author | |
chuckactor 
Senior Member 
Joined: August-20-2013 Location: Ft Collins CO Status: Offline Points: 102 |
 Post Options
 Thanks(0)
 Quote Reply
 Topic: Frozen distributorPosted: July-06-2016 at 11:13pm |
|
I used nickel anti-seize. I learned to avoid copper anti-seize from working on salt water boats. I fixed it by adding a separate ground... the one that came with the electronic ignition.
Chuck |
|
 |
|
|
Lakeview
Senior Member
Joined: January-06-2004 Location: Branchville NJ Status: Offline Points: 247 |
Post Options
Thanks(0)
Quote Reply
Posted: July-05-2016 at 3:09pm |
|
Well after approx 9 hours total of soaking,prying,chieseling,and pounding from underneath the Dizzy,it broke loose Monday morning-The suprising part is the only thing holding it in was about an 1/8"" of surface rust on the top-shaft teeth pristine clean ????
New one ordered-will definitely get nickel anti seize. |
|
|
Lakeview
1992 Barefoot Nautique 1967 Barracuda SS 1967 Chris Craft Cavalier |
|
|
|
|
8122pbrainard
Grand Poobah 
Joined: September-14-2006 Location: Three Lakes Wi. Status: Offline Points: 41045 |
Post Options
Thanks(0)
Quote Reply
Posted: July-04-2016 at 4:06pm |
I do like the idea but what grade of anti-seize did you use? The nickel rather than the off the shelf copper would have been my choice. Also, if using the anti, I suggest running a ground jumper to the distributor body. |
|
|
|
|
chuckactor
Senior Member
Joined: August-20-2013 Location: Ft Collins CO Status: Offline Points: 102 |
Post Options
Thanks(0)
Quote Reply
Posted: July-04-2016 at 2:09pm |
|
It's a curse of the 85's... http://www.correctcraftfan.com/forum/forum_posts.asp?TID=33000
When you are done, don't make the mistake I did. I slathered the new distributor in anti-seize. Worked great but next summer, I developed a bad ground which caused me a lot of pain trying to figure out my hard start issue. Chuck |
|
|
|
|
Lakeview
Senior Member
Joined: January-06-2004 Location: Branchville NJ Status: Offline Points: 247 |
Post Options
Thanks(0)
Quote Reply
Posted: July-02-2016 at 10:48am |
|
Thanks Pete-always a new learning process tinkering with these Correct Craft's
|
|
|
Lakeview
1992 Barefoot Nautique 1967 Barracuda SS 1967 Chris Craft Cavalier |
|
|
|
|
8122pbrainard
Grand Poobah
Joined: September-14-2006 Location: Three Lakes Wi. Status: Offline Points: 41045 |
Post Options
Thanks(0)
Quote Reply
Posted: July-01-2016 at 10:04pm |
|
Jim,
Take a look at this thread. A slide hammer was used after the soaking with the 50-50. |
|
|
|
|
Lakeview
Senior Member
Joined: January-06-2004 Location: Branchville NJ Status: Offline Points: 247 |
Post Options
Thanks(0)
Quote Reply
Posted: July-01-2016 at 9:55pm |
|
Trying to bring an 85 SN back and the distributor is frozen/rusted to the block even tho cast iron and aluminum are not supposed to fuse together- tried 50/50 trans fl n marvel, beat with a cold chisel at the base - it won't move
All suggestions appreciated |
|
|
Lakeview
1992 Barefoot Nautique 1967 Barracuda SS 1967 Chris Craft Cavalier |
|
|
|
|
Post Reply
|
|
Tweet
|
| Forum Jump | Forum Permissions You cannot post new topics in this forum You cannot reply to topics in this forum You cannot delete your posts in this forum You cannot edit your posts in this forum You cannot create polls in this forum You cannot vote in polls in this forum |
Topic Options
chuckactor wrote: