Boats For Sale:
Secondary Not Opening? |
Post Reply 
|
| Author | |
behindpropeller 
Platinum Member 
Joined: July-31-2006 Status: Offline Points: 1810 |
 Post Options
 Thanks(0)
 Quote Reply
 Topic: Secondary Not Opening?Posted: August-21-2006 at 1:30pm |
|
We found out the problem this weekend:
Weak coil! In the end it had nothing to do with the carb!! Tim |
|
 |
|
|
boat dr
Grand Poobah 
Joined: June-27-2004 Location: United States Status: Offline Points: 4245 |
Post Options
Thanks(0)
Quote Reply
Posted: August-20-2006 at 10:07am |
|
Tim D can you attach photos of this is done???which boat is moved first,what do you do with old parts,lottsa questions........
|
|
|
|
|
jholton
Groupie 
Joined: July-20-2006 Location: United States Status: Offline Points: 51 |
Post Options
Thanks(0)
Quote Reply
Posted: August-18-2006 at 1:26pm |
|
You can adjust you secondarys by changing the spring. Summit sells a kit for this. However no matter what spring is in the sec diaphram it should still open if there is not a vacuum leak or linkage problem. The springs are to time the opening for any particular engine.
|
|
|
|
|
GottaSki
Grand Poobah
Joined: April-21-2005 Location: NE CT Status: Offline Points: 3363 |
Post Options
Thanks(0)
Quote Reply
Posted: August-17-2006 at 10:03pm |
|
IF the linkage is right, then open the sec diaphram cover and check its scondition.
|
|
|
"There is nothing, absolutely nothing, half so much worthwhile as messing around with boats...simply messing."
River Rat to Mole |
|
|
|
|
tommer12
Senior Member 
Joined: February-05-2004 Location: United States Status: Offline Points: 366 |
Post Options
Thanks(0)
Quote Reply
Posted: August-17-2006 at 3:45pm |
|
I would still put a vacuum gauge on it and adjust accordingly to highest possible vacuum you can at idle. But that's a good point.. is the gasket between the carb and intake on or did it get replaced also?
http://www.tocmp.com/manuals/Carbs/Holley/H4V-4150-60-80/HolleyB150_html/MCarbHollB150_0042.htm |
|
|
|
|
behindpropeller
Platinum Member
Joined: July-31-2006 Status: Offline Points: 1810 |
Post Options
Thanks(0)
Quote Reply
Posted: August-17-2006 at 9:56am |
|
79-
Ill have him check these tonight and report back. Tim- We have been teasing him about his MC. He even drives a correct craft in our ski show. Tim |
|
|
|
|
Tim D
Grand Poobah
Joined: August-23-2004 Location: United States Status: Offline Points: 2641 |
Post Options
Thanks(0)
Quote Reply
Posted: August-16-2006 at 11:41pm |
|
Pick the carb up, back the MC out from under it and park a CC under the carb and attach.
|
|
|
Tim D
|
|
|
|
|
79nautique
Grand Poobah
Joined: January-27-2004 Location: United States Status: Offline Points: 7872 |
Post Options
Thanks(0)
Quote Reply
Posted: August-16-2006 at 9:46pm |
|
give this a try because you cann't adjust the vaccum the motor makes. You need to make sure that the cable is adjusted correctly and you are getting full throttle. So move the morse control to wide open, full throttle, then look at the carb and make sure that the lower throttle plate of the carb is straight up and down, you may have to open the top butterfly maunaully to see.
if it is not straight up and down or vertivcal then the cable isn't adjusted correctly and the seconadaries will never open. Did you use a gasket between the intake and spacer plate and another one between the spacer plate and carb. Do you have an edlebrck intake? are you using the adapter plate you have to have? did yo connect the PCV hose to the spacer plate. Can you post pictures of your setup? |
|
|
|
|
behindpropeller
Platinum Member
Joined: July-31-2006 Status: Offline Points: 1810 |
Post Options
Thanks(0)
Quote Reply
Posted: August-16-2006 at 7:49pm |
|
Ok so I read through the holley carb install manual but the secondary is not opening at all. Im confused.
Tim |
|
|
|
|
behindpropeller
Platinum Member
Joined: July-31-2006 Status: Offline Points: 1810 |
Post Options
Thanks(0)
Quote Reply
Posted: August-16-2006 at 7:30pm |
|
It has a brand new 4160 on it. It also has a brand new fuel pump on it. Just for kicks we took my spare 4160 and threw it on, same problem.
How do you adjust the vacuum on the carb? Tim |
|
|
|
|
tommer12
Senior Member
Joined: February-05-2004 Location: United States Status: Offline Points: 366 |
Post Options
Thanks(0)
Quote Reply
Posted: August-16-2006 at 5:00pm |
|
Sounds like your friends needs a nautique... just jokin.
check this link out: http://www.recarbco.com/technical/newtrouble.html You could possibly have a bad fuel pump or vaccum leak. If you replaced it with a brand new 4160, and the plate still does not open, you can probably leave the carb out and look at other things, which would be pump and vaccum. Plus, if you replaced the carb, did you adjust the vaccum on it? I know on my old 84' I had to adjust this after I replaced my 4160. good luck |
|
|
|
|
JoeinNY
Grand Poobah
Joined: October-19-2005 Location: United States Status: Offline Points: 5698 |
Post Options
Thanks(0)
Quote Reply
Posted: August-16-2006 at 9:43am |
|
First I would check to make sure the throttle is adjusted correctly and is fully opening the throttle plate on the carb
|
|
|
|
|
behindpropeller
Platinum Member
Joined: July-31-2006 Status: Offline Points: 1810 |
Post Options
Thanks(0)
Quote Reply
Posted: August-16-2006 at 9:39am |
|
Guys-
My friend with a 350 in his MC has been having some issues with his boat. Apparently the secondary on his carb is not opening? He just put a brand new 4160 on it and afer we manually opened the secondary it ran great. We figured it was the carb so I gave him my spare 4160 to try out. It did the same thing. Anything to try? Tim |
|
|
|
|
Post Reply
|
|
Tweet
|
| Forum Jump | Forum Permissions You cannot post new topics in this forum You cannot reply to topics in this forum You cannot delete your posts in this forum You cannot edit your posts in this forum You cannot create polls in this forum You cannot vote in polls in this forum |
Topic Options