Boats For Sale:
Anyone ever pulled apart Commander manifolds? |
Post Reply 
|
| Author | |
zwoobah 
Senior Member 
Joined: September-13-2018 Location: Providence RI Status: Offline Points: 308 |
 Post Options
 Thanks(0)
 Quote Reply
 Topic: Anyone ever pulled apart Commander manifolds?Posted: June-02-2020 at 8:23pm |
|
Looks like I've answered my own question. Hardin Marine sells new Glenwood elbows. They're a match. Now I just need to decide whether I want to spend $350 in parts to fix these. Plus the likely broken studs when I pull off my stock manifolds....
https://www.hardin-marine.com/p-13331-22-degree-elbow-aluminum-satin-finish.aspx |
|
|
1968 Mustang 16 - 351W powered
|
|
 |
|
|
zwoobah
Senior Member
Joined: September-13-2018 Location: Providence RI Status: Offline Points: 308 |
Post Options
Thanks(0)
Quote Reply
Posted: June-02-2020 at 8:10pm |
|
Made time to work on these manifolds today. Pressure test at 25psi showed them leaking only from the log to elbow gasket, so I moved forward with disassembly. Quite a few of the studs broke and separating them required a lot of small increment work with a hammer and chisel. The studs are steel and the manifolds are alu so there was galvanic corrosion on the hardware.
The logs look fine inside. The elbows have these giant holes on the inside of the water jacket. One of them had been taken apart in the past and it looks like someone laid a screen material over the hole, which then blew out. I'm not sure what caused these holes, though it looks like corrosion. Any suggestions on how to move forward? They have a "241-" part number stamped on them.    
|
|
|
1968 Mustang 16 - 351W powered
|
|
|
|
|
zwoobah
Senior Member
Joined: September-13-2018 Location: Providence RI Status: Offline Points: 308 |
Post Options
Thanks(0)
Quote Reply
Posted: December-09-2018 at 9:31pm |
|
Great, that makes it easier
|
|
|
1968 Mustang 16 - 351W powered
|
|
|
|
|
8122pbrainard
Grand Poobah 
Joined: September-14-2006 Location: Three Lakes Wi. Status: Offline Points: 41045 |
Post Options
Thanks(0)
Quote Reply
Posted: December-09-2018 at 8:43pm |
No, on the Commander's, the water jacket isn't connected between the manifold and elbows. That's why there's a cooling water hose feeding the elbow. |
|
|
|
|
zwoobah
Senior Member
Joined: September-13-2018 Location: Providence RI Status: Offline Points: 308 |
Post Options
Thanks(0)
Quote Reply
Posted: December-09-2018 at 8:28pm |
|
I plan to pressure test the manifolds - but I believe this requires removing the elbow and making a block-off plate. Am I correct?
Here's some better photos - unfortunately it's tough to get light inside the manifold and simultaneously get the camera to focus on the right spot. I think the water pass through is the open collar in the foreground. The large corroded holes slightly further in look like rot to me.   
|
|
|
1968 Mustang 16 - 351W powered
|
|
|
|
|
8122pbrainard
Grand Poobah
Joined: September-14-2006 Location: Three Lakes Wi. Status: Offline Points: 41045 |
Post Options
Thanks(0)
Quote Reply
Posted: December-08-2018 at 7:34am |
Chris, It's hard to tell from the pictures but to me the holes look like the water inlets to the exhaust cavities. Keep in mind the holes would be rough and not machined.since the elbows are sand cast. As mentioned, do presssure test the actual manifolds. |
|
|
|
|
zwoobah
Senior Member
Joined: September-13-2018 Location: Providence RI Status: Offline Points: 308 |
Post Options
Thanks(0)
Quote Reply
Posted: December-07-2018 at 11:19pm |
|
These holes are not part of the design. This is the worst of the two manifolds but they both need new elbows. This one had some water in it when I pulled it off the motor. Shame too - they polished up real nice. Swim platform came out nice at least.
  .
|
|
|
1968 Mustang 16 - 351W powered
|
|
|
|
|
8122pbrainard
Grand Poobah
Joined: September-14-2006 Location: Three Lakes Wi. Status: Offline Points: 41045 |
Post Options
Thanks(0)
Quote Reply
Posted: December-06-2018 at 9:49am |
|
Yes, Joe is correct that there are holes between the exhaust and water cavities in the elbows. That's where the water enters the exhaust. Pressure test the manifolds before fighting with getting the elbows off.
BTW, having the manifolds exposed would not cause the erosion but if, they were ever run without cooling water, it doesn't take long for the hot exhaust gases to trash aluminum manifolds. |
|
|
|
|
JoeinNY
Grand Poobah
Joined: October-19-2005 Location: United States Status: Offline Points: 5698 |
Post Options
Thanks(0)
Quote Reply
Posted: December-06-2018 at 9:35am |
|
There are some holes in the inner jacket of the elbows that are intended to be there- if you are just trying to inspect a cheap camere might be the best way to proceed.
|
|
|
|
|
KENO
Grand Poobah
Joined: June-06-2004 Location: United States Status: Offline Points: 11127 |
Post Options
Thanks(0)
Quote Reply
Posted: December-06-2018 at 9:00am |
|
You're in for some fun kid
 I guess you got the free American Skier after all If you read page 8 and 9 of the link, you'll see some discussion about these manifolds and getting the ends off Actually, read the whole thread there's a lot of info and plenty of great entertainment value mixed in. link |
|
|
|
|
zwoobah
Senior Member
Joined: September-13-2018 Location: Providence RI Status: Offline Points: 308 |
Post Options
Thanks(0)
Quote Reply
Posted: December-06-2018 at 1:22am |
|
Pulled these off a parts boat today. They polish up well, but unfprtunately they were left outside on an engine without an intake manifold and they got some water inside them. Inner jacket on the elbow pieces have some rot holes. I want to see what the water jacket looks like inside the aluminum manifold itself.
I’ve pulled the nuts joining the elbow to the manifold and it won’t come apart. Before I go crazy using force, is there any trick to this? 
|
|
|
1968 Mustang 16 - 351W powered
|
|
|
|
|
Post Reply
|
|
Tweet
|
| Forum Jump | Forum Permissions You cannot post new topics in this forum You cannot reply to topics in this forum You cannot delete your posts in this forum You cannot edit your posts in this forum You cannot create polls in this forum You cannot vote in polls in this forum |
Topic Options
zwoobah wrote: