Boats For Sale:
Oil Pressure Sending Unit- CEL- Help |
Post Reply 
|
| Author | |
KENO 
Grand Poobah 
Joined: June-06-2004 Location: United States Status: Offline Points: 11116 |
 Post Options
 Thanks(0)
 Quote Reply
 Topic: Oil Pressure Sending Unit- CEL- HelpPosted: July-31-2022 at 3:43pm |
 |
|
|
Skifunseeker01
Newbie 
Joined: July-27-2011 Status: Offline Points: 19 |
Post Options
Thanks(0)
Quote Reply
Posted: July-31-2022 at 2:19pm |
|
Keno- thanks for the short term fix and I did get my ski in. Thanks again.
|
|
|
|
|
KENO
Grand Poobah
Joined: June-06-2004 Location: United States Status: Offline Points: 11116 |
Post Options
Thanks(0)
Quote Reply
Posted: July-30-2022 at 12:09pm |
|
If you unplug both the oil pressure and water temperature switches, you won't go into limp mode..........just call it troubleshooting to make sure everything else is good and go skiing hopefully
|
|
|
|
|
Skifunseeker01
Newbie
Joined: July-27-2011 Status: Offline Points: 19 |
Post Options
Thanks(0)
Quote Reply
Posted: July-30-2022 at 9:36am |
|
Keno, thanks for the info. I'll take a good look at the T and the oil pressure switch. I looked on Nautiques.com website and didn't see a replacement switch available- only the oil pressure sending unit- which I swapped out. Like I said, the oil pressure gauge is acting up but that shouldn't cause the limp mode. I hope it is just a simple fix. I'm off to the boat and will give a follow up. Cheers Dave
|
|
|
|
|
KENO
Grand Poobah
Joined: June-06-2004 Location: United States Status: Offline Points: 11116 |
Post Options
Thanks(0)
Quote Reply
Posted: July-30-2022 at 7:35am |
|
You must be mixing up your websites, you haven't posted anything here since 2016 and it wasn't about this problem
Limp mode doesn't get a signal from your oil pressure sending unit but there's a tee right at the unit that has an oil pressure switch in it. That sends the signal to the computer for limp mode at 5 psi or less oil pressure or if the switch goes bad and fails in the low direction If you're sure your pressure is good, unplug the switch and your light should go out and you won't be in limp mode any more. There's also a water temperature switch that will put it in limp mode. That could get unplugged too. At 205ish degrees that switch which is independent from the temperature sending unit puts you in limp mode. Those are the only 2 things that put you in limp mode.
|
|
|
|
|
Skifunseeker01
Newbie
Joined: July-27-2011 Status: Offline Points: 19 |
Post Options
Thanks(0)
Quote Reply
Posted: July-30-2022 at 7:25am |
|
I should add in that my oil pressure gauge is acting up too- I give it a tap on the dash and reads correctly, sometimes it bounces but that didn't put the engine in limp mode nor did it trigger the CEL.
|
|
|
|
|
Skifunseeker01
Newbie
Joined: July-27-2011 Status: Offline Points: 19 |
Post Options
Thanks(0)
Quote Reply
Posted: July-30-2022 at 7:16am |
|
My 1999 SN 196 with a GT 40 5.8 has the CEL is on and the boat goes into limp mode right at start up. Last week the CEL was going on after a set or two and the boat would go into limp mode but we would rev the engine up and it would stop. Folks here thought it was the oil sending unit so I I swapped that out, but with the new one the CEL is on at start up. The engine goes right to limp mode. Any thoughts? Bad sensor or is there a relay or something else I can reset or replace. I'll lose the boat to for the rest of the summer if it has to go to the shop. Any suggestions would be great.
|
|
|
|
|
Post Reply
|
|
Tweet
|
| Forum Jump | Forum Permissions You cannot post new topics in this forum You cannot reply to topics in this forum You cannot delete your posts in this forum You cannot edit your posts in this forum You cannot create polls in this forum You cannot vote in polls in this forum |
Topic Options