Boats For Sale:
Arjay at work |
Post Reply 
|
Page 12> |
| Author | |
nates78ski 
Platinum Member 
Joined: January-24-2005 Location: United States Status: Offline Points: 1041 |
 Post Options
 Thanks(0)
 Quote Reply
 Topic: Arjay at workPosted: February-14-2007 at 9:17am |
|
wow! that is once Smooooooth floor! Nice job Hasbeen.
Nate |
|
 |
|
|
hasbeenskier
Platinum Member
Joined: May-23-2005 Location: United States Status: Offline Points: 1116 |
Post Options
Thanks(0)
Quote Reply
Posted: February-14-2007 at 5:44am |
|
The photo above is a shot up under the bow. Notice the 3" PVC cap. It was an after thought. In the bottom of the hull there is a small cavity along the bow stem back to the bulkhead in front of the battery box. IF any water gets in...remove the cap insert shop vac hose and suck up the water. I do not think it will be needed but that deck is not coming up
|
|
|
hasbeenskier
|
|
|
|
|
hasbeenskier
Platinum Member
Joined: May-23-2005 Location: United States Status: Offline Points: 1116 |
Post Options
Thanks(0)
Quote Reply
Posted: February-14-2007 at 5:29am |
|
|
|
hasbeenskier
|
|
|
|
|
hasbeenskier
Platinum Member
Joined: May-23-2005 Location: United States Status: Offline Points: 1116 |
Post Options
Thanks(0)
Quote Reply
Posted: February-14-2007 at 5:28am |
|
|
|
hasbeenskier
|
|
|
|
|
hasbeenskier
Platinum Member
Joined: May-23-2005 Location: United States Status: Offline Points: 1116 |
Post Options
Thanks(0)
Quote Reply
Posted: February-14-2007 at 5:26am |
|
|
|
hasbeenskier
|
|
|
|
|
hasbeenskier
Platinum Member
Joined: May-23-2005 Location: United States Status: Offline Points: 1116 |
Post Options
Thanks(0)
Quote Reply
Posted: February-14-2007 at 5:25am |
|
|
|
hasbeenskier
|
|
|
|
|
hasbeenskier
Platinum Member
Joined: May-23-2005 Location: United States Status: Offline Points: 1116 |
Post Options
Thanks(0)
Quote Reply
Posted: February-14-2007 at 5:24am |
|
|
|
hasbeenskier
|
|
|
|
|
hasbeenskier
Platinum Member
Joined: May-23-2005 Location: United States Status: Offline Points: 1116 |
Post Options
Thanks(0)
Quote Reply
Posted: February-14-2007 at 4:51am |
|
Madd Man, It is an 81 I have been working on for two years. I brought out the foam stringer pics for the stringer discussion. I am getting close to completion on this boat. I remounted a freshly painted winshield last night. The custom deck is done. Starting to do the intrument cluster complete with new wire harness.The engine and Tranny are sitting on a pallet ready to drop back in. Still to do... Reinstall steering and Morse throttle a$$embly Build a new teak swim platform,build a replica C.C.#3 trailer and repaint graphics.....Okay close to completion is a relative statement...closer than I have been.
|
|
|
hasbeenskier
|
|
|
|
|
MaddMarxx
Platinum Member
Joined: June-29-2006 Location: United States Status: Offline Points: 1741 |
Post Options
Thanks(0)
Quote Reply
Posted: February-13-2007 at 10:37pm |
|
HB..Looking good , what year is that boat?
|
|
|
|
|
hasbeenskier
Platinum Member
Joined: May-23-2005 Location: United States Status: Offline Points: 1116 |
Post Options
Thanks(0)
Quote Reply
Posted: February-13-2007 at 8:26pm |
|
It should last a hundred years
|
|
|
hasbeenskier
|
|
|
|
|
hasbeenskier
Platinum Member
Joined: May-23-2005 Location: United States Status: Offline Points: 1116 |
Post Options
Thanks(0)
Quote Reply
Posted: February-13-2007 at 8:23pm |
|
|
|
hasbeenskier
|
|
|
|
|
hasbeenskier
Platinum Member
Joined: May-23-2005 Location: United States Status: Offline Points: 1116 |
Post Options
Thanks(0)
Quote Reply
Posted: February-13-2007 at 8:22pm |
|
|
|
hasbeenskier
|
|
|
|
|
hasbeenskier
Platinum Member
Joined: May-23-2005 Location: United States Status: Offline Points: 1116 |
Post Options
Thanks(0)
Quote Reply
Posted: February-13-2007 at 8:17pm |
|
|
|
hasbeenskier
|
|
|
|
|
hasbeenskier
Platinum Member
Joined: May-23-2005 Location: United States Status: Offline Points: 1116 |
Post Options
Thanks(0)
Quote Reply
Posted: February-13-2007 at 8:16pm |
|
|
|
hasbeenskier
|
|
|
|
|
hasbeenskier
Platinum Member
Joined: May-23-2005 Location: United States Status: Offline Points: 1116 |
Post Options
Thanks(0)
Quote Reply
Posted: February-13-2007 at 8:12pm |
|
Eric. Correct Craft abandoned fir sringers in 1993. For those of you that choose wood I say, "That is why they make Chocolate and Vanilla"
|
|
|
hasbeenskier
|
|
|
|
|
eric lavine
Grand Poobah 
Joined: August-13-2006 Location: United States Status: Offline Points: 13413 |
Post Options
Thanks(0)
Quote Reply
Posted: February-13-2007 at 7:33pm |
|
I havnt ever seen anything but wood to this point, I dont think anyone has had a chance to tear into a new one yet, if thier using composites im sure there would be some type of re-bar. the down fall of wood is rot but it is strong because of the grain and once you gla$$ it in it's virtually un-destructable
|
|
|
"the things you own will start to own you"
|
|
|
|
|
jbear
Grand Poobah
Joined: January-21-2005 Location: Lake Wales FL. Status: Offline Points: 8193 |
Post Options
Thanks(0)
Quote Reply
Posted: February-11-2007 at 10:26pm |
|
Threadjack; Lake check the "Wish you were ...." thread.
john |
|
|
"Loud pipes save lives"
AdamT sez "I'm Canadian and a beaver lover myself"... |
|
|
|
|
The Lake
Platinum Member
Joined: May-13-2005 Location: Lk Winnebago MO Status: Offline Points: 1157 |
Post Options
Thanks(0)
Quote Reply
Posted: February-11-2007 at 10:13pm |
|
Eric,
What does Correct Craft use in new construction for stringers? Chuck |
|
|
|
|
eric lavine
Grand Poobah
Joined: August-13-2006 Location: United States Status: Offline Points: 13413 |
Post Options
Thanks(0)
Quote Reply
Posted: February-11-2007 at 8:19pm |
|
hard composites have no give and are so hard that they will have a tendency to break, with wood it does have a grain and will bend and stress and not break.... there is a right place for wood and a right place for man made materials. the only other thing that i would use in place of wood for stringers is aluminum
|
|
|
"the things you own will start to own you"
|
|
|
|
|
hasbeenskier
Platinum Member
Joined: May-23-2005 Location: United States Status: Offline Points: 1116 |
Post Options
Thanks(0)
Quote Reply
Posted: February-11-2007 at 8:15pm |
|
I have said it before and I think the best thing Correct craft ever did was construct the engine cradle beginning in 1980. It eliminated the lag bolting of motor mounts. Through bolts from side to side is the way to go. I did tap 3/8" aluminum stock for the bolts to grab on the outside of the stringers.
|
|
|
hasbeenskier
|
|
|
|
|
boat dr
Grand Poobah
Joined: June-27-2004 Location: United States Status: Offline Points: 4245 |
Post Options
Thanks(0)
Quote Reply
Posted: February-11-2007 at 7:34pm |
|
bj, approve of the composite vs wood in a lot of appications,stringers would be a hard sell for me.Attaching the motor mounts is going to be the key, but this can be overcome with a little thought,alm. fabricated bracket embedded in said stringer would be an idea,then drill and tap to fit motor mounts.
entertained the idea on the '64 about 1/2 way thru ,finished up the repair with 2x10 oak,soaked with West System,bedded the manicured and dressed timber followed by two layers of 10 oz. followed by the heavy rove,4 coats later the weave is barely visable.2 coats Awlgrip finished that project,Will be a long time till i attack another stringer job,be it mine or for a client.....................boat dr |
|
|
|
|
hasbeenskier
Platinum Member
Joined: May-23-2005 Location: United States Status: Offline Points: 1116 |
Post Options
Thanks(0)
Quote Reply
Posted: February-11-2007 at 6:55pm |
|
Boat Doc, I am pleased you approve. I second guess myself all the time. I prefer to chew cabbage once. I gel coated ther rudder table today and plan to rea$$emble the winshield tomorrow after work. I am monitoring Eric's work on 87BFN's boat and it makes me shutter cause I have an 81 BFN to do next. I gotta say though no wood for me I am sold on composite materials. bj
|
|
|
hasbeenskier
|
|
|
|
|
boat dr
Grand Poobah
Joined: June-27-2004 Location: United States Status: Offline Points: 4245 |
Post Options
Thanks(0)
Quote Reply
Posted: February-11-2007 at 3:28pm |
|
TRB, my bitch about the p/coat is not the finish it is the adhesion of the p/coat to the base metal.
these are just the problems i see. boat dr |
|
|
|
|
TRBenj
Grand Poobah
Joined: June-29-2005 Location: NWCT Status: Offline Points: 21182 |
Post Options
Thanks(0)
Quote Reply
Posted: February-11-2007 at 1:44pm |
|
Doc, I had my windshield powdercoated and the finish came out great. Shouldnt the powder prove to be more durable than paint?
|
|
|
|
|
boat dr
Grand Poobah
Joined: June-27-2004 Location: United States Status: Offline Points: 4245 |
Post Options
Thanks(0)
Quote Reply
Posted: February-11-2007 at 1:06pm |
|
hasbeen,I have found that all the hype of the powder coat is very over rated,sorry bout that 79,works well in other places but not in the marine world.CZ 11/zinc chromate is nasty stuff,blah,blah, blah, but the half life is about 50yrs. if applied correctly,you did rite.
The Awlgrip a wise choice also,do it right ,and ya do it only once.....boat dr P/coat has a perfect finish and looks great when it comes off in sheets,just what i have seen in real life on boat parts,,,,,,, |
|
|
|
|
hasbeenskier
Platinum Member
Joined: May-23-2005 Location: United States Status: Offline Points: 1116 |
Post Options
Thanks(0)
Quote Reply
Posted: February-11-2007 at 12:48pm |
|
It was an option I considered. I even have a customer that is in the business that powder coated the engine cradle and seat brackets for free. The painting however, I could do myself and chose to.
|
|
|
hasbeenskier
|
|
|
|
|
79nautique
Grand Poobah
Joined: January-27-2004 Location: United States Status: Offline Points: 7872 |
Post Options
Thanks(0)
Quote Reply
Posted: February-11-2007 at 11:20am |
|
why didn't you just powder coat them instead?
|
|
|
|
|
hasbeenskier
Platinum Member
Joined: May-23-2005 Location: United States Status: Offline Points: 1116 |
Post Options
Thanks(0)
Quote Reply
Posted: February-11-2007 at 8:06am |
|
These pieces were shot with Awlgrip yesterday and I will let them sit for a couple of days for it has been cool here for the last few days.
Ski-di-up! |
|
|
hasbeenskier
|
|
|
|
|
hasbeenskier
Platinum Member
Joined: May-23-2005 Location: United States Status: Offline Points: 1116 |
Post Options
Thanks(0)
Quote Reply
Posted: February-11-2007 at 8:03am |
|
|
|
hasbeenskier
|
|
|
|
|
hasbeenskier
Platinum Member
Joined: May-23-2005 Location: United States Status: Offline Points: 1116 |
Post Options
Thanks(0)
Quote Reply
Posted: February-11-2007 at 8:01am |
|
While I am at it I might as well show you the windshield pieces and a$$orted other parts primed with zinc chromate and ready for painting with Black Awlgrip.
|
|
|
hasbeenskier
|
|
|
|
|
Post Reply
|
Page 12> |
Tweet
|
| Forum Jump | Forum Permissions You cannot post new topics in this forum You cannot reply to topics in this forum You cannot delete your posts in this forum You cannot edit your posts in this forum You cannot create polls in this forum You cannot vote in polls in this forum |
Topic Options