Polishing Brass Rudder & Strut

Message Topic Search Topic Options Post Reply Create New Topic Printable Version Translate Topic

   Reid, I apply with a paper towel or a rag. It will turn black with some elbow grease. Then buff off with clean towel. Very similar to other metal polishes. It does have a strong amonia odor. I use it on all types of metal and it is very cheap compared to mother's and duragloss.

Author	Message Topic Search Topic Options Post Reply Create New Topic Printable Version Translate Topic
Tim D Members Profile Send Private Message Find Members Posts Add to Buddy List Grand Poobah Joined: August-23-2004 Location: United States Status: Offline Points: 2641	Post Options Post Reply Quote Tim D Report Post Thanks(0) Quote Reply Topic: Polishing Brass Rudder & Strut Posted: October-14-2004 at 5:55pm
	Reid, I apply with a paper towel or a rag. It will turn black with some elbow grease. Then buff off with clean towel. Very similar to other metal polishes. It does have a strong amonia odor. I use it on all types of metal and it is very cheap compared to mother's and duragloss.
	Tim D

reidp Members Profile Send Private Message Find Members Posts Add to Buddy List Platinum Member Joined: December-06-2003 Location: Mooresville, NC Status: Offline Points: 1804	Post Options Post Reply Quote reidp Report Post Thanks(0) Quote Reply Posted: October-12-2004 at 9:15pm
	Tim, How do you apply the Blue Magic? Can you just rub it on? I'd like something easy and quick enough to where you could stand to do it more often. Thanks.
	ReidP 1973 Mustang

Tim D Members Profile Send Private Message Find Members Posts Add to Buddy List Grand Poobah Joined: August-23-2004 Location: United States Status: Offline Points: 2641	Post Options Post Reply Quote Tim D Report Post Thanks(0) Quote Reply Posted: October-12-2004 at 5:21pm
	Go to Walmart and get Blue magic in the auto section. It will make it shine.
	Tim D

79nautique Members Profile Send Private Message Find Members Posts Add to Buddy List Grand Poobah Joined: January-27-2004 Location: United States Status: Offline Points: 7872	Post Options Post Reply Quote 79nautique Report Post Thanks(0) Quote Reply Posted: October-12-2004 at 2:48pm
	I had the same deal on the strut bushings. It's not a problem just insert the bushings from each end until flush and tighten down the set screws. The hard part is getting the old one out.

reidp Members Profile Send Private Message Find Members Posts Add to Buddy List Platinum Member Joined: December-06-2003 Location: Mooresville, NC Status: Offline Points: 1804	Post Options Post Reply Quote reidp Report Post Thanks(0) Quote Reply Posted: October-12-2004 at 1:06pm
	As for the polishing, if you've got a heavy duty 90 deg. polisher, put some rubbing compound on the pad and go at it. It'll make a black mess, but it'll shine it up. Or you can get some Never-Dull or other metal polish and go at it by hand for weeks. Only thing is, either way, it'll still tarnish back rather quickly. Anyone ever try clear-coating the underwater gear to keep it shiny after polishing? Someone else on the strut bearing? My last one resembled the original in length. Reid
	ReidP 1973 Mustang

SkiLew Members Profile Send Private Message Find Members Posts Visit Members Homepage Add to Buddy List Groupie Joined: May-20-2004 Location: United States Status: Offline Points: 73	Post Options Post Reply Quote SkiLew Report Post Thanks(0) Quote Reply Posted: October-12-2004 at 11:03am
	What can I use to polish my brass strut, rudder,& fins on my 1978 CC. I had to take my rudder off to replace the shaft so this would be a good opportunity to polish it. I also am going to replace the bushing in my strut and two 2" bearings came in from Discount Inboard Marine vs the one original 6" bearing that is currently installed. Is this acceptable?

Polishing Brass Rudder & Strut

About CCF

Donate

Partners

Contact