1955 Atom Skier Updates |
Post Reply | Page <1234 5> |
Author | |
nates78ski
Platinum Member Joined: January-24-2005 Location: United States Status: Offline Points: 1041 |
Post Options
Thanks(0)
|
I'm not sure if i'm allowed to ask questions anymore, but I was wondering if the light green paint on all of the stringers/framing is original, or is it grey. Because we're about to start cleaning up the framing & we figured we should know this now & get the paint soon. I'm hoping the green's original... it looks cooler than grey
Nate |
|
8122pbrainard
Grand Poobah Joined: September-14-2006 Location: Three Lakes Wi. Status: Offline Points: 41045 |
Post Options
Thanks(0)
|
Nate,
Yes you're allowed to ask questions! I told you I'd still be around to help! Here's a paragraph out of the "68 Chris" thread regarding bilge paints in Correct Crafts: "Chris's were at least consistent and actually used a bilge paint like most wood boat builders did. Now, with wood Correct Crafts, I've seen enough of them to know they would through all their left over paints and solvent washes in a bucket and call it "bilge" paint!!! My Atom is a mix of green and gray!!" I must say however that I am very surprised about you being concerned about the original color of the bilge paint!! Any pictures of your dads boats yet? |
|
nates78ski
Platinum Member Joined: January-24-2005 Location: United States Status: Offline Points: 1041 |
Post Options
Thanks(0)
|
Pete, wondering if this pylon looks like it could be for my Atom... looking at possibly picking it up...
Pylon Thanks, Nate |
|
Terp
Senior Member Joined: November-12-2008 Location: Deep Creek Lake Status: Offline Points: 339 |
Post Options
Thanks(0)
|
Nate, the ring and finger look different from mine but see if they can shoot you a pic of the base.
Pete, did they change the pylon between '55 & '64? If not, I've got a good shot of the base and the R&F of mine here...'64 Atom pylon Nate, I'll be back home early on the 1st and can get measurements off mine if Pete (or someone else) says they're the same. |
|
nates78ski
Platinum Member Joined: January-24-2005 Location: United States Status: Offline Points: 1041 |
Post Options
Thanks(0)
|
New Pictures Uploaded... We just got the new stringers in yesterday, they're only clamped in place at the moment, as we're waiting for bolts, but soon. Even with just the clamps, it's amazing how much they stiffen up the boat as compared to the old ones...
Nate |
|
8122pbrainard
Grand Poobah Joined: September-14-2006 Location: Three Lakes Wi. Status: Offline Points: 41045 |
Post Options
Thanks(0)
|
John, Sorry but I missed your post/question while I was up north for Christmas and New Years. I just caught it when Nate brought the tread back to the top. Yes, the 50's and 60's pylons are different. The 50's were anywhere from a chrome pipe if exposed to a painted pipe if under a section of deck. John, your picture is a great example. The ring and finger was simply a 3/4" round shaft onto which the ring and finger were welded on and then chromed. The early 60's pylons were really the first ones made with any consistency. They too were made with pipe and stepped larger by inserting/welding larger and larger pipe towards the bottom. I think it was 3 steps. The 1" ring and finger into 1" pipe. the 1&1/4" pipe and then 1&1/2" pipe. Nate, The pylon you found on ebay isn't a CC. To me, it's a 70's generic (after market). |
|
nates78ski
Platinum Member Joined: January-24-2005 Location: United States Status: Offline Points: 1041 |
Post Options
Thanks(0)
|
Stringers bolted in as well as new chines in place & screwed in. Everything's painted & ready for the plywood.
Link to pictures in Signature Nate |
|
8122pbrainard
Grand Poobah Joined: September-14-2006 Location: Three Lakes Wi. Status: Offline Points: 41045 |
Post Options
Thanks(0)
|
Nate,
Looking good!! Sure brings back some memories! I do have a question. Is that paint on the frames bonding surfaces to the hull? Are you planning on using 5200 or epoxy to bond the ply to the frames? Ether way, if paint, it's not the greatest for adhesion. |
|
boat dr
Grand Poobah Joined: June-27-2004 Location: United States Status: Offline Points: 4245 |
Post Options
Thanks(0)
|
Pete give me a call if you get a chance.................Boat dr
|
|
farmer
Senior Member Joined: July-23-2006 Location: United States Status: Offline Points: 442 |
Post Options
Thanks(0)
|
Nate,the Atom looks great! What kind of wood did you use for the chines and frames? Gary |
|
Watch your fingers.
|
|
nates78ski
Platinum Member Joined: January-24-2005 Location: United States Status: Offline Points: 1041 |
Post Options
Thanks(0)
|
Gary,
For the chines we went with air dried oak and for the frames (we only replaced 1.5) we used Phillipine Mahogany. We're looking to start getting the bottom on tonight after work & tomorrow depending on if we head up to the Detroit Boat Show... Nate |
|
nates78ski
Platinum Member Joined: January-24-2005 Location: United States Status: Offline Points: 1041 |
Post Options
Thanks(0)
|
Pete, here's some pictures of my dads old 1939 Chris Craft 15.6ft Deluxe Runabout that you asked about a while back...
Sashay Nate |
|
8122pbrainard
Grand Poobah Joined: September-14-2006 Location: Three Lakes Wi. Status: Offline Points: 41045 |
Post Options
Thanks(0)
|
Nate,
Nice!! Does he still have it? Is that you in your younger years standing on the dock in the red shorts? |
|
nates78ski
Platinum Member Joined: January-24-2005 Location: United States Status: Offline Points: 1041 |
Post Options
Thanks(0)
|
Thanks Pete, No he doesn't have it anymore. & no, in the first picture with someone in it that's my older brother in the red shorts standing on the sailboat.. I think when that picture was taken I would have been around 5-6 years old & then the later one with Sashay in the background & the paddle boat in front of it, I'm the one in the water, pondering how i'm going to get into the boat, with my brother sitting in it. I think i was probably 7-8 at that point.
Nate |
|
nates78ski
Platinum Member Joined: January-24-2005 Location: United States Status: Offline Points: 1041 |
Post Options
Thanks(0)
|
The bottom is on the atom as of Saturday afternoon. No pictures yet, because of some weird shadows that we were getting taking them, but i'll have some up soon.
The Sides are next... Hopefully this Weekend!! Nate |
|
75 stang
Senior Member Joined: August-11-2008 Location: northwest ohio Status: Offline Points: 475 |
Post Options
Thanks(0)
|
Looking good! Ill bet those plywood sides go on a lot faster than these planks I'm working on! I didn't see if you were using any 5200 on the frames, I think that stuff is better than the screws for holding power.
Get those pics up... We should be puttng on sides this week as well. later |
|
nates78ski
Platinum Member Joined: January-24-2005 Location: United States Status: Offline Points: 1041 |
Post Options
Thanks(0)
|
We 5200'd all the frames & battens just before laying the sheeting down. the 5200 definitely has some holding power, but from my past uses of it & my understanding of it. It's basically a glorified caulk... so the screws will stay in Besides, we already drilled all those holes in the plywood... we'll have to fill them anyhow
Nate |
|
nates78ski
Platinum Member Joined: January-24-2005 Location: United States Status: Offline Points: 1041 |
Post Options
Thanks(0)
|
The Sides ARE ON!!!
Not gonna lie, i'm pretty geeked about it. Actually looks like a boat again. Though, the work's nowhere near finished, it's nice to see it like this. Pistures updates in Sig. Nate |
|
boat dr
Grand Poobah Joined: June-27-2004 Location: United States Status: Offline Points: 4245 |
Post Options
Thanks(0)
|
Nate , did you get my E Mail? give me a call about W/S Brackets..........Billy
|
|
75 stang
Senior Member Joined: August-11-2008 Location: northwest ohio Status: Offline Points: 475 |
Post Options
Thanks(0)
|
Lookin' good! Im going to have to play catch up now...
|
|
nates78ski
Platinum Member Joined: January-24-2005 Location: United States Status: Offline Points: 1041 |
Post Options
Thanks(0)
|
Get At it Sean!
Billy, Got your email, took pictures this morning uploading them as we speak at work & I will email them to you in about 5 minutes. Nate |
|
nates78ski
Platinum Member Joined: January-24-2005 Location: United States Status: Offline Points: 1041 |
Post Options
Thanks(0)
|
the bottom was fiberglassed this past Tuesday night, with 2 more coats of epoxy since then. Epoxied the sides Saturday morning, so they're ready to be sanded a bit & painted, though I believe we're holding off on painting the sides until we flip it over to start working on the decks & the interior. Ordering bottom paint today, hope to have the bottom painted by the end of the week & maybe have her flipped over by Saturday.
My pictures in the signature on Photobucket were updated today, the last of those pictures is from Tuesday night right after 'glassing the bottom. Probably wont update it until we get it painted & Flipped. Enjoy! Nate |
|
nates78ski
Platinum Member Joined: January-24-2005 Location: United States Status: Offline Points: 1041 |
Post Options
Thanks(0)
|
Got the Atom Primed & bottom painted this past week.
Also got her flipped over this afternoon... Ready to start on the topside. The Sides will get painted once we get alot more of the inside of the boat finished, so that we don't have to be quite as careful hopping into & out of the boat as to not mar the sides. Nate |
|
8122pbrainard
Grand Poobah Joined: September-14-2006 Location: Three Lakes Wi. Status: Offline Points: 41045 |
Post Options
Thanks(0)
|
Nate,
You're making progress! You think you'll have it in the water in a couple months? Any work on the engine? I just noticed you haven't put any spray rails on the hull. Are you leaving them off? |
|
nautique frk
Platinum Member Joined: February-16-2004 Location: United States Status: Offline Points: 1784 |
Post Options
Thanks(0)
|
Nate, That is looking really Nice !!!!!!
|
|
nates78ski
Platinum Member Joined: January-24-2005 Location: United States Status: Offline Points: 1041 |
Post Options
Thanks(0)
|
Pete,
We just got the valve guides we'd been waiting on for the last month or so. So the motor is ready to put back together, clean up & paint. Also, As for the spray rails, we're going to put them back on, but they'll go on before we paint the sides... probably sometime over the next month or so. & yes, i'm still shooting for an Early June deadline. Though with the way my early june is shaping up... it won't matter if it's finished then, it probably won't get launched until mid-late June. Thanks Mike! Nate |
|
bkhallpass
Grand Poobah Joined: March-29-2005 Location: United States Status: Offline Points: 4723 |
Post Options
Thanks(0)
|
Nate,
Are you finally going to get in the darned car and show up at Green Lake this year. It would be great if you had the Atom in tow, but it would be fine if you brought the 78 as well. Actually, it would be fine if you just showed up. BKH |
|
Livin' the Dream
|
|
81nautique
Grand Poobah Joined: September-03-2005 Location: Big Rock, Il Status: Offline Points: 5779 |
Post Options
Thanks(0)
|
Great progress Nate, I love the fact that your doing this with your dad.
Ditto what Brian said, Green Lake or bust. |
|
You can’t change the wind but you can adjust your sails
|
|
nates78ski
Platinum Member Joined: January-24-2005 Location: United States Status: Offline Points: 1041 |
Post Options
Thanks(0)
|
Thanks guys.
Yeah i've been toying with the idea of Green Lake. My only thing is it's like 2 weeks out from my 2 A Triathlons this year.... i'm not sure how that'd work into my training schedule. Nate |
|
boat dr
Grand Poobah Joined: June-27-2004 Location: United States Status: Offline Points: 4245 |
Post Options
Thanks(0)
|
Nate, Pete and I are gonna need to see some "OLD WOOD" . You never know I may be thru with the Dart by then.If so your woody will have some company. Now if we can get Pete to bring his.
Would that not be too cool, The Dart is a 1949 Your Atom is a '50s I am sure we will have a '60s boat or two A bunch of '70s And of course the '80s The 90 year models And then, here comes the '00 That would give us Seven Generations of CC boats gatherd at one place......Boat dr |
|
Post Reply | Page <1234 5> |
Tweet
|
Forum Jump | Forum Permissions You cannot post new topics in this forum You cannot reply to topics in this forum You cannot delete your posts in this forum You cannot edit your posts in this forum You cannot create polls in this forum You cannot vote in polls in this forum |