Need new pump housing

Message Topic Search Topic Options Post Reply Create New Topic Printable Version Translate Topic

   Waketique78:  Email me the numbers cast into your waterpump housing.  Better yet, do that and email me a really good closeup picture of it showing the cover screws and cover in place and a second picture of your impeller.

I will try to help you get it rebuilt cheaply.  If your housing is shot, give up and buy a new pump... I'm pretty sure I can help you there as well.

Author	Message Topic Search Topic Options Post Reply Create New Topic Printable Version Translate Topic
25XS Members Profile Send Private Message Find Members Posts Add to Buddy List Newbie Joined: October-31-2005 Location: United States Status: Offline Points: 16	Post Options Post Reply Quote 25XS Report Post Thanks(0) Quote Reply Topic: Need new pump housing Posted: October-31-2005 at 5:51pm
	Waketique78: Email me the numbers cast into your waterpump housing. Better yet, do that and email me a really good closeup picture of it showing the cover screws and cover in place and a second picture of your impeller. I will try to help you get it rebuilt cheaply. If your housing is shot, give up and buy a new pump... I'm pretty sure I can help you there as well.
	"Stock Stuff" by day... Racing Mercury outboards on the weekends. 1991 Nautique Excel "thousands" of hours...

waketique78 Members Profile Send Private Message Find Members Posts Add to Buddy List Newbie Joined: September-15-2005 Location: United States Status: Offline Points: 36	Post Options Post Reply Quote waketique78 Report Post Thanks(0) Quote Reply Posted: October-19-2005 at 11:21am
	the housing is vinyl/plastic. I don't really see any problem with the plastic housing because it has lasted quite a while on the boat. Also, this might sound dumb, but I just can't seem to find where to hook up a house to my motor so I can run it in the driveway and winterize it. I have the commander 302. if anyone with that motor could give me some help I would appreciate it.
	1978 Ski Tique, Skylon, Fatseat And Sacs for ballast

woodyelc Members Profile Send Private Message Find Members Posts Add to Buddy List Senior Member Joined: February-17-2004 Location: orlando Status: Offline Points: 378	Post Options Post Reply Quote woodyelc Report Post Thanks(0) Quote Reply Posted: October-18-2005 at 2:38pm
	CALL WOODY AT 407 851 1965 HAVE PUMP AND INSTRUCTIONS ON MOUNTING PUMP TO MOTOR.
	woodyelc

Tim D Members Profile Send Private Message Find Members Posts Add to Buddy List Grand Poobah Joined: August-23-2004 Location: United States Status: Offline Points: 2641	Post Options Post Reply Quote Tim D Report Post Thanks(0) Quote Reply Posted: October-18-2005 at 11:18am
	One thing about the newer pumps is the shaft is so much longer. Either fab a new bracket to move the pump back if there's room or take it to a machine shop and have the shaft shortened.
	Tim D

nuttyskier2002 Members Profile Send Private Message Find Members Posts Add to Buddy List Gold Member Joined: September-28-2005 Location: United States Status: Offline Points: 669	Post Options Post Reply Quote nuttyskier2002 Report Post Thanks(0) Quote Reply Posted: October-18-2005 at 8:54am
	That price sounds a little high for the whole pump. Don't forget you'll want to install a new seal and bearing. Now for that housing,...what is it made of. Was your original one plastic or brass. I'll bet the one that was offered to you by midwest cc is plastic. I'd still consider going with a new one that has a brass body. Skidim sells a Sherwood belt driven pump for $206.00. Just my 2 cents.
	95 Malibu Echelon w/Mercruiser 350 Magnum Skier Former boats: 88 Ski Centurion Tru Trac II 59 Chris Craft Capri (woody)

waketique78 Members Profile Send Private Message Find Members Posts Add to Buddy List Newbie Joined: September-15-2005 Location: United States Status: Offline Points: 36	Post Options Post Reply Quote waketique78 Report Post Thanks(0) Quote Reply Posted: October-18-2005 at 8:22am
	well i just talked to midwest correct craft. And they offer the housing for 70 and the impeller for 30. Or the whole pump for 317. So I think I will go with the new housing and rebuild the pump myself. And yes it is the raw water/belt driven pump
	1978 Ski Tique, Skylon, Fatseat And Sacs for ballast

nuttyskier2002 Members Profile Send Private Message Find Members Posts Add to Buddy List Gold Member Joined: September-28-2005 Location: United States Status: Offline Points: 669	Post Options Post Reply Quote nuttyskier2002 Report Post Thanks(0) Quote Reply Posted: October-17-2005 at 11:32pm
	If you need a new housing and impeller both, I believe it would be wise to just replace the whole pump. Yours is belt driven (as opposed to crank mounted) right? Check out the pumps that Skidim sells. There are several other places that sell raw water pumps for inboards as well. I'll bet that you'll spend more money trying to buy the housing and impeller separately than you will just replacing the whole thing. Write back if you need help finding one.
	95 Malibu Echelon w/Mercruiser 350 Magnum Skier Former boats: 88 Ski Centurion Tru Trac II 59 Chris Craft Capri (woody)

waketique78 Members Profile Send Private Message Find Members Posts Add to Buddy List Newbie Joined: September-15-2005 Location: United States Status: Offline Points: 36	Post Options Post Reply Quote waketique78 Report Post Thanks(0) Quote Reply Posted: October-17-2005 at 12:36pm
	I need a new pump housing for my 1978 Ski Tique with the ford 302. Mine has heat cracks in it. The problem I am having is a I can't seem to find the right pump on any websites? can anybody help me?
	1978 Ski Tique, Skylon, Fatseat And Sacs for ballast

Need new pump housing

About CCF

Donate

Partners

Contact