351 cracked block

Message Topic Search Topic Options Post Reply Create New Topic Printable Version Translate Topic

   I have 351 that i didnt drain good enuff. The block cracked and broke the piston and a valve. Im in the process of looking for a motor. Does anyone have any advice about remanufatured engines? I would like to have over 300 hp.

Author	Message Topic Search Topic Options Post Reply Create New Topic Printable Version Translate Topic
NautiqueExpress Members Profile Send Private Message Find Members Posts Add to Buddy List Newbie Joined: February-01-2006 Location: United States Status: Offline Points: 2	Post Options Post Reply Quote NautiqueExpress Report Post Thanks(0) Quote Reply Topic: 351 cracked block Posted: March-08-2006 at 7:48pm
	I have 351 that i didnt drain good enuff. The block cracked and broke the piston and a valve. Im in the process of looking for a motor. Does anyone have any advice about remanufatured engines? I would like to have over 300 hp.

tonydjd Members Profile Send Private Message Find Members Posts Add to Buddy List Groupie Joined: December-29-2005 Location: United States Status: Offline Points: 80	Post Options Post Reply Quote tonydjd Report Post Thanks(0) Quote Reply Posted: March-08-2006 at 7:58pm
	Jasper I'm not sure I only new a friend that bought a set up from them a little expensive
	Old School 88

79nautique Members Profile Send Private Message Find Members Posts Add to Buddy List Grand Poobah Joined: January-27-2004 Location: United States Status: Offline Points: 7872	Post Options Post Reply Quote 79nautique Report Post Thanks(0) Quote Reply Posted: March-09-2006 at 5:56am
	too get the 300hp you will have to get a class II engine from them and it runs around $3500.00

NautiqueExpress Members Profile Send Private Message Find Members Posts Add to Buddy List Newbie Joined: February-01-2006 Location: United States Status: Offline Points: 2	Post Options Post Reply Quote NautiqueExpress Report Post Thanks(0) Quote Reply Posted: March-09-2006 at 6:25am
	I found a site that rebuilds motors. He said a remanufactured engine with heads would be around $1400 delivered with 285hp(www.RapidoMarine.com). This is the cheapest I have seen. Are there any high performance cams for a reverse rotating engine?

79nautique Members Profile Send Private Message Find Members Posts Add to Buddy List Grand Poobah Joined: January-27-2004 Location: United States Status: Offline Points: 7872	Post Options Post Reply Quote 79nautique Report Post Thanks(0) Quote Reply Posted: March-09-2006 at 11:00am
	yes there are hi po cams for reverse rotation engines most have to be custom ordered. Keep in mind you get what you pay for and 1400 is pretty cheap now but when you have to replace it again in a couple of years where's the saving then?

79nautique Members Profile Send Private Message Find Members Posts Add to Buddy List Grand Poobah Joined: January-27-2004 Location: United States Status: Offline Points: 7872	Post Options Post Reply Quote 79nautique Report Post Thanks(0) Quote Reply Posted: March-09-2006 at 11:04am
	Also you need to figure core cost. 90% of the shops want a rebuildable core and your block isn't rebuildable, so you'll need to figure in the core charge as well, Jasper will take anything that doesn't have a visible hole or defect on it looking from the outside. Most shop's tear the engine down and check to make sure it's a good block before they give you creadit for the core.

Bob's2001 Members Profile Send Private Message Find Members Posts Add to Buddy List Senior Member Joined: March-28-2005 Location: Lake Jackson TX Status: Offline Points: 241	Post Options Post Reply Quote Bob's2001 Report Post Thanks(0) Quote Reply Posted: March-09-2006 at 10:50pm
	62 wood had an engine for sale a while back. 300 hp, still on the crate. Check and see if he still has it. It was in the parts for sale forum.
	Bob Ed 83 2001

Dallas Members Profile Send Private Message Find Members Posts Add to Buddy List Groupie Joined: February-08-2005 Location: United States Status: Offline Points: 46	Post Options Post Reply Quote Dallas Report Post Thanks(0) Quote Reply Posted: March-10-2006 at 6:46am
	Sorry to hear about your motor issues. I had the same thing happen a couple of years ago ; I got cought deployed away from home a little longer than expected, plus a very early freez. I ended up building a 393 stroker and reused all of the EFI parts on from my motor and the periferals. Its a monster now producing just under 400 hp and at least as much torque. PCM Provides A and B motors throgh there dealers at greatly reduced prices. These motors for one reason or another are not 100% brand new; they may have a blemish, or have had a part swapped out for some reason. You can get a lot of motor for a significant saving, then recover a little bit of the cost by selling off what parts are salvageable from your motor. Best of luck Dallas

TRBenj Members Profile Send Private Message Find Members Posts Add to Buddy List Grand Poobah Joined: June-29-2005 Location: NWCT Status: Online Points: 21186	Post Options Post Reply Quote TRBenj Report Post Thanks(0) Quote Reply Posted: March-10-2006 at 8:48am
	Dallas, I'd like to hear a little more about your motor. Besides the stroker kit, what other mods does it have (heads, cam, exhaust, etc)? Any mods needed to the EFI system to get proper fuel flow? I would imagine that motor would push your TSC into the low 50's.

79nautique Members Profile Send Private Message Find Members Posts Add to Buddy List Grand Poobah Joined: January-27-2004 Location: United States Status: Offline Points: 7872	Post Options Post Reply Quote 79nautique Report Post Thanks(0) Quote Reply Posted: March-10-2006 at 10:33am
	I would say it's also a standard rotation engine and not a reverse rotation. If it is rev what did you do about the crank and it's grind?

351 cracked block

About CCF

Donate

Partners

Contact