x

Mike,
Welcome to CCfan. The next question is typically - we want pictures!!

Regarding the trans, you have some internal issues with the pump. That front seal does not see any pressure unless the pump is shot by-passing oil around it. I suggest a rebuild but, make sure the shop knows what they are doing. Here in the states and as mentioned, Eric would be the ONLY person I would trust.

mdills wrote: Cost to much to ship that thing.

If $100 is too much to know that the trans will be rebuilt correctly, then you may want to reconsider boat ownership!

mdills wrote: You think a local trans rebuild shop could do it right?

Your guess is as good as ours. Who knows what they charge too... theres a very good chance that you'll come out ahead pricewise even factoring in the shipping to Ohio, AND you'll get a known good transmission back.

Theres a reason people told you to send it to Eric!

Do NOT attempt to rebuild it yourself.

x

Bri892001 wrote: mdills wrote: ...Cost to much to ship that thing... It says in your user profile that you work for UPS. Stop charging yourself so much for shipping!

I know right.. Darn Union causes our prices to be so high, along with fuel price gone up.

Mike,
Eric usually stops in every morning but give him a call.

That "local trans shop" if automotive is the worst choice. A marine and automotive trans do not have anything in common except for the fluid they use. Do you know the basic concepts on how a marine trans works? If the shop is marine, then I still feel it's a bad choice. We have some horror story threads about "pro" shops. Rebuilding it yourself is also risky - some here have tried but very few have succeeded.

Send it up to Eric on the next FedEx truck! They tend to be less expensive. Find yourself one of the plastic milk crates and make a plywood top for it. The trans will fit nicely in it and the built in handles make handling the weight easy.

BuffaloBFN wrote: I sent one from N Ga to Eric. It was around $100 or a bit over. He'll be along soon. Welcome aboard neighbor.

I still think Mike should get a quote from FedEx!!

x

8122pbrainard wrote: BuffaloBFN wrote: I sent one from N Ga to Eric. It was around $100 or a bit over. He'll be along soon. Welcome aboard neighbor. I still think Mike should get a quote from FedEx!!

I shipped UPS and it came back by Fedex...

mdills wrote: Greg, It must be nice to live so close to Lake lanier...I stay on Lake Allatonna or Lake Weiss.. each an hour away..

As with most things, it has its highs and lows. Right now it's 12 feet low.

We do a Hoochie(Chattahoochee) run sometimes, maybe we'll see you then. There are a few threads in the reunion section.

emccallum wrote: 8122pbrainard wrote: emccallum wrote: I know a guy on lake Murray, SC that has worked for pcm for years and he rebuilds them. Ernest, I see the decision to send it to Eric has already been made which is great. Did you happen to notice the trans is a B/W Velvet and not a PCM? Yes I did. My inference was that the guy is very familiar with inboards and working on them. Not well stated, I agree. I think it is great that he is sending the trans to Eric as Eric contributes a lot to this forum.   When he started talking about doing it himself and shipping costs, I just wanted him to have another option closer to home .

Got it!! Good guys are hard to come by.

His name is Gene....cant recall his last name at the moment. He fixed a couple of friends velvet drives this year. One poor kid had his tranny worked on by a local "expert" then a year later he finally got his engine back in and running, and the rebuilt tranny went out first day. Turns out the "expert" didnt have a circlip on propelry and all the clutch packs were loose!

mdills wrote: I know you replace the damper plate, but do you have to get a new cooler line?

If they are in good shape I don´t see why change them...again, lines are not that expensive. The oil cooler is a part i´d inspect also...