Boats For Sale:
Exhaust install |
Post Reply 
|
| Author | |
Riley 
Grand Poobah 
Joined: January-19-2004 Location: Portland, ME Status: Offline Points: 7953 |
 Post Options
 Thanks(0)
 Quote Reply
 Topic: Exhaust installPosted: September-11-2012 at 6:53pm |
|
Has anyone done their exhaust like this? We're trying to do it similar as Correct Craft did in the 70's, but after doing one side it seems overly complicated and I'm not crazy about the joints under the floor. It is floating now and will need to be supported if we go with it. I'm interested in how others may have done it. The short piece of hose is just slipped over the tube to keep it from chaffing on the steering block bolt.
  
|
|
 |
|
|
watrski
Senior Member 
Joined: December-01-2010 Location: Chippewa Lake Status: Offline Points: 393 |
Post Options
Thanks(0)
Quote Reply
Posted: September-11-2012 at 6:56pm |
|
Are you glassing over the hose?
|
|
|
Tubing Sucks.
|
|
|
|
|
Riley
Grand Poobah
Joined: January-19-2004 Location: Portland, ME Status: Offline Points: 7953 |
Post Options
Thanks(0)
Quote Reply
Posted: September-11-2012 at 7:01pm |
|
No. Putting a plywood floor down and putting vinyl flooring on it. The floor will be removalable, but not easily.
|
|
|
|
|
75 Tique
Grand Poobah
Joined: August-12-2004 Location: Seven Lakes, NC Status: Offline Points: 6130 |
Post Options
Thanks(0)
Quote Reply
Posted: September-11-2012 at 7:01pm |
|
Bruce,
What is over complicated about that? It looks just like my Tique looks and I assume mine is as it came from the factory. Admittedly, I haven't had the floor out, but I have replaced the front hose and have dug around the back with the gas tank out. Instead of the rubber sleeve, there is some of that old astro turf carpet wrapped around the pipe. |
|
|
_____________
“So, how was your weekend?” “Well, let me see…sun burn, stiff neck, screwed up back, assorted aches and pains….yup, my weekend was great, thanks for asking.” |
|
|
|
|
Riley
Grand Poobah
Joined: January-19-2004 Location: Portland, ME Status: Offline Points: 7953 |
Post Options
Thanks(0)
Quote Reply
Posted: September-11-2012 at 7:10pm |
|
Larry, a straight shot with rubber seemed too easy snd with no joints under the floor. I'm going to go back and look at it in a day or two, but wasn't all that thrilled with it when I finished it up. This is why our projects take so long.
|
|
|
|
|
75 Tique
Grand Poobah
Joined: August-12-2004 Location: Seven Lakes, NC Status: Offline Points: 6130 |
Post Options
Thanks(0)
Quote Reply
Posted: September-11-2012 at 7:16pm |
|
Easier, yes, but you know, there are those here that will say the improved exhaust note is worth the effort. There are also those who will passionately advocate that having the pipe is more original.
Is that your new Cuda (color doesnt look quite right but I know it was waiting for a new motor and the strips on the back seem cuda-esque. |
|
|
_____________
“So, how was your weekend?” “Well, let me see…sun burn, stiff neck, screwed up back, assorted aches and pains….yup, my weekend was great, thanks for asking.” |
|
|
|
|
cphase
Gold Member 
Joined: May-11-2010 Location: Newnan, GA Status: Offline Points: 795 |
Post Options
Thanks(0)
Quote Reply
Posted: September-11-2012 at 7:17pm |
Thats the way my boat is now, rubber from the riser to the transom. |
|
|
|
|
storm34
Grand Poobah
Joined: November-03-2008 Location: Dexter Iowa Status: Offline Points: 4492 |
Post Options
Thanks(0)
Quote Reply
Posted: September-11-2012 at 7:17pm |
|
Only thing I would change is the connection under the cross member for accessibility reasons. It would be a pain to put clamps on underneath that board. Otherwise, it looks great...and will sound great.
Here is a picture of my 78 Tique and how the exhaust came from the factory before we removed the mufflers and replaced with copper. 
|
|
|
|
|
cphase
Gold Member
Joined: May-11-2010 Location: Newnan, GA Status: Offline Points: 795 |
Post Options
Thanks(0)
Quote Reply
Posted: September-11-2012 at 7:22pm |
|
You may want to consider a more vertical run off the risers like Chris' Tique above. That will let the floor get closer to the engine compartment.
|
|
|
|
|
TRBenj
Grand Poobah
Joined: June-29-2005 Location: NWCT Status: Offline Points: 21186 |
Post Options
Thanks(0)
Quote Reply
Posted: September-11-2012 at 7:23pm |
|
Bruce, it looks good- stop worrying! Thats the way its done. Same number of connections as if you had mufflers in the boat (as many CC's did).
|
|
|
|
|
75 Tique
Grand Poobah
Joined: August-12-2004 Location: Seven Lakes, NC Status: Offline Points: 6130 |
Post Options
Thanks(0)
Quote Reply
Posted: September-11-2012 at 7:24pm |
|
Interesting the difference from 76 to 78. One, I dont have mufflers, just copper pipe, and two, my copper pipes are under the floor. Although I am not sure, but I THINK my floor might have been redone. Unfortunately, not the stringers, but I think the floor is new, so maybe they were covered then. As far as clamp under the board, mine is kind of like that. That is why when I had to replace a hose, I had to dig out the gas tank and undo the hose in the rear so I could slide the whole mess forward, to replace that front connection, then slide the whole mess back and redo the connection in the rear
|
|
|
_____________
“So, how was your weekend?” “Well, let me see…sun burn, stiff neck, screwed up back, assorted aches and pains….yup, my weekend was great, thanks for asking.” |
|
|
|
|
Riley
Grand Poobah
Joined: January-19-2004 Location: Portland, ME Status: Offline Points: 7953 |
Post Options
Thanks(0)
Quote Reply
Posted: September-11-2012 at 7:26pm |
|
That is the Cuda and we are going to all this trouble just for the improved exhaust note. Tubes aren't original to the 1966 boats. Finally got the motor in. It was supposed to be ready for this summer, but not enough hours in the day. Next summer!
 Chris that joint ended up under the board because that is the point where it levels out on the floor. I tried a more downward angle, but it makes for a sharper corner and those elbows are meant provide a straighter shot. The motor box is plenty big to cover everything up, 54" long on the bottom and 33' wide. Tim, I was ready to go buy new hose, but I knew I'd end up having all these parts in the garage forever. |
|
|
|
|
Post Reply
|
|
Tweet
|
| Forum Jump | Forum Permissions You cannot post new topics in this forum You cannot reply to topics in this forum You cannot delete your posts in this forum You cannot edit your posts in this forum You cannot create polls in this forum You cannot vote in polls in this forum |
Topic Options
Riley wrote: