Boats For Sale:
Mast Light |
Post Reply 
|
| Author | |
skyfuzz 
Senior Member 
Joined: August-17-2004 Location: South Florida Status: Offline Points: 239 |
 Post Options
 Thanks(0)
 Quote Reply
 Topic: Mast LightPosted: September-12-2016 at 2:26pm |
|
I don't like the visible mast light wiring on my boat's windshield. Anyone familiar with these old CC know if the wiring can be run through the aluminum window frame and down through the bottom? Aren't the frames hollow for the most part? Pix 1 & 3 are pre-restoration pix.
  
|
|
|
http://www.correctcraftfan.com/diaries/details.asp?ID=7613&sort=&pagenum=1
|
|
 |
|
|
fanofccfan
Platinum Member 
Joined: December-13-2009 Location: North Bend NE Status: Offline Points: 1781 |
Post Options
Thanks(0)
Quote Reply
Posted: September-12-2016 at 3:43pm |
|
That's exactly the setup I had. Removed it because I did not like it at all. I wondered about the wire routing myself but never took the time. I just live without it and hope the small light on the back is sufficient. So far it has been.
|
|
|
|
|
AAM196
Gold Member
Joined: October-23-2012 Location: Pittsburgh, PA Status: Offline Points: 846 |
Post Options
Thanks(0)
Quote Reply
Posted: September-12-2016 at 5:01pm |
|
LOL... I thought I was about to see a correct craft sail boat.
|
|
|
|
|
8122pbrainard
Grand Poobah 
Joined: September-14-2006 Location: Three Lakes Wi. Status: Offline Points: 41045 |
Post Options
Thanks(1)
Quote Reply
Posted: September-12-2016 at 5:10pm |
|
Robert,
The frame extrusions are hollow but it may not be that easy. I'd use a bell hangers bit to drill down the center from the top. |
|
|
|
|
skyfuzz
Senior Member
Joined: August-17-2004 Location: South Florida Status: Offline Points: 239 |
Post Options
Thanks(0)
Quote Reply
Posted: September-12-2016 at 6:06pm |
For safety sake, I would want the masthead light at the highest point on my boat when operating at night. But with the transom light on at least, there's something. I like the look of the masthead light personally. Thanks. |
|
|
http://www.correctcraftfan.com/diaries/details.asp?ID=7613&sort=&pagenum=1
|
|
|
|
|
skyfuzz
Senior Member
Joined: August-17-2004 Location: South Florida Status: Offline Points: 239 |
Post Options
Thanks(0)
Quote Reply
Posted: September-12-2016 at 6:10pm |
|
|
|
http://www.correctcraftfan.com/diaries/details.asp?ID=7613&sort=&pagenum=1
|
|
|
|
|
Little one
Groupie 
Joined: May-16-2016 Location: Monticello, in Status: Offline Points: 77 |
Post Options
Thanks(0)
Quote Reply
Posted: September-12-2016 at 10:42pm |
|
On the ski Tique windshield I removed (virtually the same frame) the left front window hooked into the right front window filling any hollow spots in the middle, you can see how it connects together by looking at the top of the window, it is the same all the way to the bottom.
|
|
|
|
|
Little one
Groupie
Joined: May-16-2016 Location: Monticello, in Status: Offline Points: 77 |
Post Options
Thanks(0)
Quote Reply
Posted: September-12-2016 at 10:44pm |
|
And my mustang has another piece of trim to cover the wires all the way down.
|
|
|
|
|
DrCC
Grand Poobah
Joined: April-12-2004 Location: at home Status: Offline Points: 2868 |
Post Options
Thanks(0)
Quote Reply
Posted: September-14-2016 at 7:03pm |
|
If you look under the dash, there should be another hole - forward and slightly port of the existing. Wire should exit in the center of the light bracket.
Take the light bracket off, you should see a hole in the w/s frame. Clothes hanger works better than an actual wire phish. And yes it will be a p-i-t-a. |
|
|
Keep it....from sinkin'
|
|
|
|
|
Post Reply
|
|
Tweet
|
| Forum Jump | Forum Permissions You cannot post new topics in this forum You cannot reply to topics in this forum You cannot delete your posts in this forum You cannot edit your posts in this forum You cannot create polls in this forum You cannot vote in polls in this forum |
Topic Options
fanofccfan wrote: