Boats For Sale:
Starter bench test |
Post Reply 
|
| Author | |
quinner 
Grand Poobah 
Joined: October-12-2005 Location: Unknown Status: Offline Points: 5828 |
 Post Options
 Thanks(0)
 Quote Reply
 Topic: Starter bench testPosted: October-19-2016 at 11:53am |
|
This sounds like a perfect application for the Timmy Two Nut T-Bag
|
|
 |
|
|
Waterdog
Grand Poobah
Joined: April-27-2006 Location: United States Status: Offline Points: 2020 |
Post Options
Thanks(0)
Quote Reply
Posted: October-19-2016 at 11:15am |
|
Just messin' with ya Pete
Your the professor & I'm Mcgiver I was waiting for the VOM 
|
|
|
|
|
8122pbrainard
Grand Poobah
Joined: September-14-2006 Location: Three Lakes Wi. Status: Offline Points: 41045 |
Post Options
Thanks(0)
Quote Reply
Posted: October-19-2016 at 10:12am |
Andy, Sorry to jump in but I didn't want Ken to just clamp the jumpers on and get the same results due to potential bad connections. Ken, If you have a VOM (volt ohm meter), get a voltage reading directly on the battery posts and then at the starter when cranking the engine. This may show a voltage drop narrowing down the problem if caused by bad connections, bad cables and maybe a bad start relay (solenoid). BTW, a starter bench test is pretty meaningless since there isn't any load on the starter. |
|
|
|
|
Waterdog
Grand Poobah
Joined: April-27-2006 Location: United States Status: Offline Points: 2020 |
Post Options
Thanks(0)
Quote Reply
Posted: October-19-2016 at 9:19am |
|
OK Pete, make sure the connections are clean...
and make sure the blinker fluid is toped off... |
|
|
|
|
8122pbrainard
Grand Poobah
Joined: September-14-2006 Location: Three Lakes Wi. Status: Offline Points: 41045 |
Post Options
Thanks(0)
Quote Reply
Posted: October-19-2016 at 9:06am |
If the jumper clamps at the battery end are clamped to the cable terminals, you may get the same results due to the potential bad connections between the cable terminals and battery posts!! |
|
|
|
|
Waterdog
Grand Poobah
Joined: April-27-2006 Location: United States Status: Offline Points: 2020 |
Post Options
Thanks(0)
Quote Reply
Posted: October-19-2016 at 8:33am |
|
Just to test the battery cables use a set of jumper cables.
If the engine turns over better - ya gota corroded cable. |
|
|
|
|
8122pbrainard
Grand Poobah
Joined: September-14-2006 Location: Three Lakes Wi. Status: Offline Points: 41045 |
Post Options
Thanks(0)
Quote Reply
Posted: October-18-2016 at 11:41pm |
|
Ken,
Regarding the lack of hole shot, was it a sudden occurrence or was it over a period of time? Has the engine had a basic tune up lately? What is the health of the engine? Have you done any testing like compression? |
|
|
|
|
Duane in Indy
Platinum Member 
Joined: October-26-2015 Location: Indiana Status: Offline Points: 1578 |
Post Options
Thanks(0)
Quote Reply
Posted: October-18-2016 at 9:47pm |
|
I vote for bad connections. Mine had same issue. Replace or redo the battery connectors on the positive cable from the solenoid to the starter.
|
|
|
Keep it as original as YOU want it
1978 Mustang (modified) |
|
|
|
|
Hollywood
Moderator Group
Joined: February-04-2004 Location: Twin Lakes, WI Status: Offline Points: 13514 |
Post Options
Thanks(0)
Quote Reply
Posted: October-18-2016 at 6:38pm |
|
Even a new deep cycle should crank up that V8 nice and strong, but do yourself a favor and swap it for a normal automotive battery if that's the case.
|
|
|
|
|
8122pbrainard
Grand Poobah
Joined: September-14-2006 Location: Three Lakes Wi. Status: Offline Points: 41045 |
Post Options
Thanks(0)
Quote Reply
Posted: October-18-2016 at 6:35pm |
+1 I agree Also worn brushes and a commutator due for a clean up. What's the condition of the battery? |
|
|
|
|
Hollywood
Moderator Group
Joined: February-04-2004 Location: Twin Lakes, WI Status: Offline Points: 13514 |
Post Options
Thanks(0)
Quote Reply
Posted: October-18-2016 at 5:49pm |
|
There's one connection, the bench test seems pretty straight forward to me. Ground the body.
You don't need to run the engine to winterize it. Get the water out, via drain plugs and disconnected hoses. The rest is warm fuzzies. Could be a bad starter but more likely corroded battery cables and or dirty/loose connections. |
|
|
|
|
klockhart
Newbie 
Joined: July-03-2006 Location: United States Status: Offline Points: 19 |
Post Options
Thanks(0)
Quote Reply
Posted: October-18-2016 at 5:40pm |
|
Looking for info on how to bench test a starter motor removed from a 1969 Correctcraft Mustang..Engine is ford 302,,, no solenoid attached to the starter,,one lead from the solenoid to the starter....Starting issues...new battery and engine turning over so slowly that its not enough to fire it up...also..during the attempt to start the negative/ground terminal at the battery gets so hot it begins to smoke.. live in northeast and need to get it running to winterize...has been running well for 12 years, most recently this spring.. however this year it would run and idle but had vertually no hole shot (tough to get up on a ski)...not giving up on this gem as it has treated my family well for 12 years!!..Any ifo would be appreciated!!!!
|
|
|
Mustang "69"
|
|
|
|
|
Post Reply
|
|
Tweet
|
| Forum Jump | Forum Permissions You cannot post new topics in this forum You cannot reply to topics in this forum You cannot delete your posts in this forum You cannot edit your posts in this forum You cannot create polls in this forum You cannot vote in polls in this forum |
Topic Options
Waterdog wrote: