Boats For Sale:
Strut bearing length importance |
Post Reply 
|
| Author | ||
DanielT 
Newbie 
Joined: July-20-2015 Location: Amsterdam Status: Offline Points: 29 |
 Post Options
 Thanks(0)
 Quote Reply
 Topic: Strut bearing length importancePosted: May-08-2017 at 11:12am |
|
|
I'm changing my strut bearing on my boat for the first time but have a question concerning the bearing length.
I live in the Netherlands where they don't seem to sell the 6" strut bearing. However they do have a 2" or 4" variant.. I was thinking I could buy three 2"s to make a 3 piece-6" bearing, What option would be best, go for the 3 piece design or the 4" one and leave a 2" gap. |
||
 |
||
|
JoeinNY
Grand Poobah 
Joined: October-19-2005 Location: United States Status: Offline Points: 5698 |
Post Options
Thanks(0)
Quote Reply
Posted: May-08-2017 at 12:24pm |
|
|
go with 2 2" with a 2" gap between them - seriously
|
||
|
||
|
DanielT
Newbie
Joined: July-20-2015 Location: Amsterdam Status: Offline Points: 29 |
Post Options
Thanks(0)
Quote Reply
Posted: May-08-2017 at 5:00pm |
|
|
Ill try that.
|
||
|
||
|
Jonny Quest
Grand Poobah
Joined: August-20-2013 Location: Utah--via Texas Status: Offline Points: 2974 |
Post Options
Thanks(0)
Quote Reply
Posted: May-08-2017 at 11:57pm |
|
|
I just changed out the strut bearing in my 1994. I'm fairly sure that it was the original strut bearing. The bearing was 6 inches long and I replaced it with a similar unit by Johnson Duramax:
LINK  JQ |
||
|
Current
2003 Ski Nautique 206 Limited Previous 2001 Ski Nautique Open Bow 1994 Ski Nautique Open Bow Aqua skiing, ergo sum |
||
|
||
|
OldSchoolBlue84
Gold Member 
Joined: December-02-2012 Location: Valparaiso, IN Status: Offline Points: 814 |
Post Options
Thanks(0)
Quote Reply
Posted: May-09-2017 at 12:08am |
|
👍+1 - did mine, looks original with great fit & quick shipping |
||
|
Kostas
1984 Ski Nautique 2001 |
||
|
||
|
DanielT
Newbie
Joined: July-20-2015 Location: Amsterdam Status: Offline Points: 29 |
Post Options
Thanks(0)
Quote Reply
Posted: May-09-2017 at 4:17am |
|
|
Unfortunately I don't have time waiting for overseas shipment, it could easily take a week or two. Plus I'd have to pay double the amount because of shipping costs.
|
||
|
||
|
SNobsessed
Grand Poobah
Joined: October-21-2007 Location: IA Status: Offline Points: 7102 |
Post Options
Thanks(0)
Quote Reply
Posted: May-09-2017 at 10:15am |
|
|
I put in separate bearings, one at each end, & it has not been a problem.
|
||
|
“Beer is proof that God loves us and wants us to be happy.”
Ben Franklin |
||
|
||
|
8122pbrainard
Grand Poobah
Joined: September-14-2006 Location: Three Lakes Wi. Status: Offline Points: 41045 |
Post Options
Thanks(0)
Quote Reply
Posted: May-09-2017 at 10:57am |
|
|
Daniel,
I totally agree with Joe and Chris that two 2" on both ends of the strut is plenty. Somewhere through history it was found out that in this case shorter is better. It was from ether radial load calculations or probably just from time monitoring wear of the rubber. In theory there is less drag on the shaft from less surface area of the rubber so there's a minuet increase in efficiency. |
||
|
||
|
KENO
Grand Poobah
Joined: June-06-2004 Location: United States Status: Offline Points: 11093 |
Post Options
Thanks(0)
Quote Reply
Posted: May-09-2017 at 5:47pm |
|
Pete You must be flashing back to your ball room dancing days or something using words like minuet. You don't seem the type 
|
||
|
||
|
8122pbrainard
Grand Poobah
Joined: September-14-2006 Location: Three Lakes Wi. Status: Offline Points: 41045 |
Post Options
Thanks(0)
Quote Reply
Posted: May-09-2017 at 7:12pm |
|
Well Ken, spelling isn't my forte and in this case, I'm blaming it on spell check. I never knew that "minute" was spelled the same as minute. I typed in some absurd spelling and then spell check took over! 
|
||
|
||
|
KENO
Grand Poobah
Joined: June-06-2004 Location: United States Status: Offline Points: 11093 |
Post Options
Thanks(0)
Quote Reply
Posted: May-09-2017 at 7:19pm |
|
|
That's OK, I never knew what the definition of minuet was till I looked it up so we both did a little learnin' today
So I guess you're not a ballroom dancer then? |
||
|
||
|
Post Reply
|
|
Tweet
|
| Forum Jump | Forum Permissions You cannot post new topics in this forum You cannot reply to topics in this forum You cannot delete your posts in this forum You cannot edit your posts in this forum You cannot create polls in this forum You cannot vote in polls in this forum |
Topic Options
Jonny Quest wrote: