could have been worse

Message Topic Search Topic Options Post Reply Create New Topic Printable Version Translate Topic

   Better than an engine block.

As you may have heard, we had quite a cold snap in NC recently, single digits and teens.  I forgot one little bit of maintenance, to empty the water out of a stoneware fountain we have on our deck.  Again, not as bad as an engine block, but I'm not sure my wife would feel the same way.  Since it is just a split or two and not crumbled I think it can be fixed, but I dont know what to use.  I was thinking 3M 5200, but not sure it would adhere.  Any other thoughts?  Pete????

Author	Message Topic Search Topic Options Post Reply Create New Topic Printable Version Translate Topic
75 Tique Members Profile Send Private Message Find Members Posts Visit Members Homepage Add to Buddy List Grand Poobah Joined: August-12-2004 Location: Seven Lakes, NC Status: Offline Points: 6130	Post Options Post Reply Quote 75 Tique Report Post Thanks(0) Quote Reply Topic: could have been worse Posted: January-10-2018 at 1:10pm
	Better than an engine block. As you may have heard, we had quite a cold snap in NC recently, single digits and teens. I forgot one little bit of maintenance, to empty the water out of a stoneware fountain we have on our deck. Again, not as bad as an engine block, but I'm not sure my wife would feel the same way. Since it is just a split or two and not crumbled I think it can be fixed, but I dont know what to use. I was thinking 3M 5200, but not sure it would adhere. Any other thoughts? Pete????
	_____________ “So, how was your weekend?” “Well, let me see…sun burn, stiff neck, screwed up back, assorted aches and pains….yup, my weekend was great, thanks for asking.”

Riley Members Profile Send Private Message Find Members Posts Add to Buddy List Grand Poobah Joined: January-19-2004 Location: Portland, ME Status: Offline Points: 7954	Post Options Post Reply Quote Riley Report Post Thanks(0) Quote Reply Posted: January-10-2018 at 1:15pm
	5200 ought to work. Most importantly, did you go the distance and pour anti freeze into the engine?

JoeinNY Members Profile Send Private Message Find Members Posts Add to Buddy List Grand Poobah Joined: October-19-2005 Location: United States Status: Offline Points: 5698	Post Options Post Reply Quote JoeinNY Report Post Thanks(0) Quote Reply Posted: January-10-2018 at 3:32pm
	I wouldn't use 5200 personally - if it is very tight break I would use super glue (cyanoacrylate). If it was a bit off I would use epoxy. 5200 might work just fine truthfully but generally gives up some adhesion to allow some flex vs an epoxy in this case you don't need the flex.
	1983 Ski Nautique 2001 1967 Mustang 302 "Decoy" Holeshot Video

baitkiller Members Profile Send Private Message Find Members Posts Visit Members Homepage Add to Buddy List Platinum Member Joined: October-11-2011 Location: SW Florida Status: Offline Points: 1693	Post Options Post Reply Quote baitkiller Report Post Thanks(0) Quote Reply Posted: January-10-2018 at 7:16pm
	FLEX SEAL! just kidding, epoxy is what I would reach for. And dont forget to tint it to match the glaze.. :)
	Jesus was a bare-footer.............

8122pbrainard Members Profile Send Private Message Find Members Posts Add to Buddy List Grand Poobah Joined: September-14-2006 Location: Three Lakes Wi. Status: Offline Points: 41045	Post Options Post Reply Quote 8122pbrainard Report Post Thanks(0) Quote Reply Posted: January-10-2018 at 7:35pm
	Larry, I too like the epoxy idea. You can get one of the epoxy duplex syringes at the hardware store. It does all the mixing for you.
	54 Atom 77 Tique 64 X55 Dunphy Keep it original, Pete <

could have been worse

About CCF

Donate

Partners

Contact