Boats For Sale:
Carb dripping from primary’s |
Post Reply 
|
| Author | |
adamo 
Newbie 
Joined: March-30-2020 Location: nc Status: Offline Points: 30 |
 Post Options
 Thanks(0)
 Quote Reply
 Topic: Carb dripping from primary’sPosted: April-06-2020 at 4:36pm |
|
I have a 84, 351 on a CC Southwind. It’s got the holly 4160 on it and when I go to start it up it starts perfectly, but it is dripping fuel from the primary’s at idle, and my biggest concern is after I shut it off it pours fuel into the intake. When I go to start it again it has a hard start like the motor is flooded. I just did a rebuild kit and it did it before as well as now. Just wondering what could cause the fuel to pour that much out of the primary’s when it’s shut off and any test I could do to help determine the cause?
|
|
 |
|
|
KENO
Grand Poobah 
Joined: June-06-2004 Location: United States Status: Online Points: 11119 |
Post Options
Thanks(0)
Quote Reply
Posted: April-06-2020 at 6:06pm |
|
That's probably the #1 most popular problem on CCF
If you click on the link below, you'll have plenty of reading, along with solutions  I'd do some reading, then ask any questions you might have link |
|
|
|
|
adamo
Newbie
Joined: March-30-2020 Location: nc Status: Offline Points: 30 |
Post Options
Thanks(0)
Quote Reply
Posted: April-06-2020 at 8:32pm |
|
I read the main couple link you sent, thank you. I replaced the power valve, needles and seats as well as the gaskets. My rebuild kit didn’t come with the accelerator pump gaskets just the ones for the carb. I have taken the carb apart again to check the float level as well as clean all the passage ways. I don’t really understand why fuel is dripping out. Could the mechanical pump have too much pressure? And if it did wouldn't the secondary be leaking too?
|
|
|
|
|
KENO
Grand Poobah
Joined: June-06-2004 Location: United States Status: Online Points: 11119 |
Post Options
Thanks(0)
Quote Reply
Posted: April-06-2020 at 9:24pm |
|
Do you have a good filter in the system so that you're not pumping junk from the gas tank into the newly cleaned carburetor and getting stuck between the the needle and seat ?
Not knowing how your primary float is set, take a look at the picture that shows a reduced level setting that can help. It's not a lot lower but usually enough to stop the overflow. The fuel pump would affect both bowls so I wouldn't worry about that yet. I'd look first at the needle and seat and system cleanliness, then if that's all good try the float adjustment. 
|
|
|
|
|
adamo
Newbie
Joined: March-30-2020 Location: nc Status: Offline Points: 30 |
Post Options
Thanks(0)
Quote Reply
Posted: April-06-2020 at 9:34pm |
|
Awsome thank you, I will try that. Does it need to be lowered because it sits on an angle? I changed the fuel filter when I did the carb as well.
|
|
|
|
|
KENO
Grand Poobah
Joined: June-06-2004 Location: United States Status: Online Points: 11119 |
Post Options
Thanks(0)
Quote Reply
Posted: April-06-2020 at 9:39pm |
Yes.............because of the angle, lowering helps
|
|
|
|
|
adamo
Newbie
Joined: March-30-2020 Location: nc Status: Offline Points: 30 |
Post Options
Thanks(0)
Quote Reply
Posted: April-06-2020 at 9:45pm |
|
That makes a lot of sense, right now it’s level, would you say all of these carbs should have the setup you showed?
|
|
|
|
|
KENO
Grand Poobah
Joined: June-06-2004 Location: United States Status: Online Points: 11119 |
Post Options
Thanks(0)
Quote Reply
Posted: April-06-2020 at 9:49pm |
|
On the 1 to 1 stuff with about a 15 degree angle, I'd say it helps on the front bowl
Leave the rear adjusted level though If it's really pouring out you might have other issues but try this for now. |
|
|
|
|
adamo
Newbie
Joined: March-30-2020 Location: nc Status: Offline Points: 30 |
Post Options
Thanks(0)
Quote Reply
Posted: April-06-2020 at 10:02pm |
|
What are you referring to as 1 to 1? The trans?
|
|
|
|
|
GottaSki
Grand Poobah
Joined: April-21-2005 Location: NE CT Status: Offline Points: 3363 |
Post Options
Thanks(0)
Quote Reply
Posted: April-06-2020 at 11:19pm |
|
As viewed, that is lowered... the bowl is upside down. so if you lower the float when viewed like that, it raises the fuel level.
|
|
|
"There is nothing, absolutely nothing, half so much worthwhile as messing around with boats...simply messing."
River Rat to Mole |
|
|
|
|
KENO
Grand Poobah
Joined: June-06-2004 Location: United States Status: Online Points: 11119 |
Post Options
Thanks(0)
Quote Reply
Posted: April-07-2020 at 8:18am |
Yep |
|
|
|
|
adamo
Newbie
Joined: March-30-2020 Location: nc Status: Offline Points: 30 |
Post Options
Thanks(0)
Quote Reply
Posted: April-08-2020 at 2:33pm |
|
Thank you guys, I lower the float and she’s running Awsome now, no more dripping or flooding.
|
|
|
|
|
MrMcD
Grand Poobah
Joined: January-28-2014 Location: Folsom, CA Status: Offline Points: 3750 |
Post Options
Thanks(0)
Quote Reply
Posted: April-08-2020 at 3:58pm |
|
Nice work Ken, another happy Correct Craft owner.
|
|
|
|
|
KENO
Grand Poobah
Joined: June-06-2004 Location: United States Status: Online Points: 11119 |
Post Options
Thanks(0)
Quote Reply
Posted: April-08-2020 at 8:23pm |
I think it should really say "nice work Adam"
|
|
|
|
|
MrMcD
Grand Poobah
Joined: January-28-2014 Location: Folsom, CA Status: Offline Points: 3750 |
Post Options
Thanks(0)
Quote Reply
Posted: April-09-2020 at 5:33am |
|
We can go with that, but it is sure nice when you really need help to get good help fast and have a good result.
|
|
|
|
|
Post Reply
|
|
Tweet
|
| Forum Jump | Forum Permissions You cannot post new topics in this forum You cannot reply to topics in this forum You cannot delete your posts in this forum You cannot edit your posts in this forum You cannot create polls in this forum You cannot vote in polls in this forum |
Topic Options
adamo wrote: