1978 Southwind Restoration |
Post Reply ![]() |
Author | |
CTYSouthwind20 ![]() Newbie ![]() Joined: October-02-2019 Location: Michigan Status: Offline Points: 30 |
![]() ![]() ![]() ![]() ![]() Posted: April-29-2021 at 10:49pm |
My engine shop did a great job on the rebuild and balancing of my 351W. We picked up the engine today, one step closer to new and perfect 78 Southwind!
We're looking for a source for a part specific to marine engines. There's a torque coupling plate between the crankshaft and transmission. Mine's in bad shape, I'm looking for any suggestions on who would provide a new one. Photo below: |
|
Charlie
|
|
![]() |
|
Jonny Quest ![]() Grand Poobah ![]() ![]() Joined: August-20-2013 Location: Utah--via Texas Status: Offline Points: 2927 |
![]() ![]() ![]() ![]() ![]() |
Call Vince at www.skidim.com
803-345-0996
|
|
Current
2003 Ski Nautique 206 Limited Previous 2001 Ski Nautique Open Bow 1994 Ski Nautique Open Bow Aqua skiing, ergo sum |
|
![]() |
|
CTYSouthwind20 ![]() Newbie ![]() Joined: October-02-2019 Location: Michigan Status: Offline Points: 30 |
![]() ![]() ![]() ![]() ![]() |
Thank you Jonny Quest, I'll call Vince tomorrow!
|
|
Charlie
|
|
![]() |
|
Jonny Quest ![]() Grand Poobah ![]() ![]() Joined: August-20-2013 Location: Utah--via Texas Status: Offline Points: 2927 |
![]() ![]() ![]() ![]() ![]() |
It’s called a damper plate. You need to provide engine and transmission info. You mentioned a Ford small block Windsor 351 above. Velvet Drive tranny?
|
|
Current
2003 Ski Nautique 206 Limited Previous 2001 Ski Nautique Open Bow 1994 Ski Nautique Open Bow Aqua skiing, ergo sum |
|
![]() |
|
KENO ![]() Grand Poobah ![]() Joined: June-06-2004 Location: United States Status: Offline Points: 10972 |
![]() ![]() ![]() ![]() ![]() |
Jonny self admittedly likes to spend other people's money. This (SkiDim plate) is a good example of that. ![]() For a 78 Southwind with a Borg Warner transmission, you can buy an ALTO/Sachs damper plate with a lot less of your money if you want. It's an ALTDA-106A talked about n the link below. You can get the 106A which is pre trimmed to fit your Ford with a Borg Warner 71C or you can get the 106 which needs trimming to fit. Here's a link to the 106A Here's a link to the 106, since the 106A may be out of stock Here's a link to what SkiDim will sell you, unless maybe they'll sell you their Chevy plate (looks and priced a lot like an ALTDA-106 ![]() Over the years, plenty of people here have used the 106A plate or bought the 106 and trimmed it themselves. The recommendation originally came from FFI marine transmissions |
|
![]() |
|
Jonny Quest ![]() Grand Poobah ![]() ![]() Joined: August-20-2013 Location: Utah--via Texas Status: Offline Points: 2927 |
![]() ![]() ![]() ![]() ![]() |
The folks at www.skidim.com are great people. I like to steer business to them whenever possible. Vince has helped out many CCF members — often without selling anything, only providing solid advice. No doubt that you can find parts cheaper elsewhere, but price isn’t my only consideration. I’ve bought many items from them over the years and will continue to do so.
JQ
|
|
Current
2003 Ski Nautique 206 Limited Previous 2001 Ski Nautique Open Bow 1994 Ski Nautique Open Bow Aqua skiing, ergo sum |
|
![]() |
|
8122pbrainard ![]() Grand Poobah ![]() ![]() Joined: September-14-2006 Location: Three Lakes Wi. Status: Offline Points: 41045 |
![]() ![]() ![]() ![]() ![]() |
Without a doubt, Vince has helped many but here Ken has, and continues to exceed at helping. The added benefit to Kens help is he always recommends a less expensive route for the same or better product.
|
|
![]() |
|
CTYSouthwind20 ![]() Newbie ![]() Joined: October-02-2019 Location: Michigan Status: Offline Points: 30 |
![]() ![]() ![]() ![]() ![]() |
Jonny and Keno, thank you both. I ended up ordering the damper plate Keno recommended, but from SkiDim. Richard at the service desk was really helpful and acknowledged that one will work "and guys use it". I like the spring design better than my OEM part. Mine had several chunks broken out of it.
I appreciate both of the sources, I hadn't heard of, or ordered from either.
|
|
Charlie
|
|
![]() |
|
Jonny Quest ![]() Grand Poobah ![]() ![]() Joined: August-20-2013 Location: Utah--via Texas Status: Offline Points: 2927 |
![]() ![]() ![]() ![]() ![]() |
Well said, Pete. KENO also exceeds at helping and providing valuable advice -- he also has a "nose" for finding good values and low prices. And you, Pete, are another CCF member that exceeds at helping and providing valuable information and advice. Thanks to all those here on CCF that generously donate your time and experience to assist our fellow Correct Craft owners. This website is an awesome resource. JQ
|
|
Current
2003 Ski Nautique 206 Limited Previous 2001 Ski Nautique Open Bow 1994 Ski Nautique Open Bow Aqua skiing, ergo sum |
|
![]() |
|
KENO ![]() Grand Poobah ![]() Joined: June-06-2004 Location: United States Status: Offline Points: 10972 |
![]() ![]() ![]() ![]() ![]() |
Aw shucks, Ken would probably say that it's good to have choices available when you're looking for parts and spending your money,
Once upon a time you had some choices to make Jonny and you're probably glad you made the choices you did on a carburetor and distributor among other things ![]() And Pete..........you're not supposed to say anything nice about me, it's not what people expect around here (us agreeing with each other), but Thanks. But be careful.............I think they might figure out that we're really the same person with multiple personalities. And.......maybe SkiDim will update their website to say that the cheap Chevy plate fits a Ford with some trimming and sell a bunch more.. |
|
![]() |
|
67 ski nat ![]() Platinum Member ![]() Joined: July-19-2018 Location: Santa rosa Status: Offline Points: 1193 |
![]() ![]() ![]() ![]() ![]() |
Excellent, ken and Pete getting along
Coming next: pictures loaded from your phone |
|
![]() |
Post Reply ![]() |
|
Tweet
|
Forum Jump | Forum Permissions ![]() You cannot post new topics in this forum You cannot reply to topics in this forum You cannot delete your posts in this forum You cannot edit your posts in this forum You cannot create polls in this forum You cannot vote in polls in this forum |