Boats For Sale:
Drive Damper Diameter |
Post Reply 
|
| Author | ||
Hysteria 
Groupie 
Joined: May-31-2020 Location: Indiana Status: Offline Points: 70 |
 Post Options
 Thanks(0)
 Quote Reply
 Topic: Drive Damper DiameterPosted: May-21-2021 at 8:30pm |
|
|
My drive damper is shot, and needs to be replaced. Since the ALTDA-106A is not available, I ordered a ALTDA-106 with the understanding that I will need to cut it down to fit the 12" flywheel on my 351. I wanted to retain some semblance of balance in the damper after hacking it up, so I 3D printed a jig that would allow me to mark a circle at exactly 12" from the center point of the splines. However, after marking it and then referencing the ALTDA-106A photo to compare, I'm seeing that they appear to be leaving a little more material on theirs and now I'm starting to doubt my method:
  I don't have the transmission pulled so can't actually see/measure anything and want to get this ready ahead of time, so I was hoping one of you guys who has been through this could set me straight. Am I ok to cut this thing down to 12" or is there a reason they are leaving them a little larger? What holes will I end up using when I bolt this thing on?
|
||
 |
||
|
KENO
Grand Poobah 
Joined: June-06-2004 Location: United States Status: Offline Points: 11112 |
Post Options
Thanks(0)
Quote Reply
Posted: May-21-2021 at 8:36pm |
|
|
From a recent post
You'd be cutting right through the right mounting holes.  Cut it like the picture shows. Edit looking at the plate in your picture and the plate in my picture, one picture is the front and one is the back, so you'd probably be OK, but I'd still cut it like the picture shows
|
||
|
||
|
Hysteria
Groupie
Joined: May-31-2020 Location: Indiana Status: Offline Points: 70 |
Post Options
Thanks(0)
Quote Reply
Posted: May-21-2021 at 8:49pm |
|
I'm glad I asked. Both of these photos are of the back of the damper, so you were right the first time, I would have cut right through the mounting hole that I need. As usual, what seems like a good idea on paper doesn't translate to the real world. I'm a big fan of your artwork by the way, this serves more of a purpose than a lot of other "art" out there  edit: oh duh, you used a different photo for yours. Nevermind me
|
||
|
||
|
KENO
Grand Poobah
Joined: June-06-2004 Location: United States Status: Offline Points: 11112 |
Post Options
Thanks(0)
Quote Reply
Posted: May-21-2021 at 8:59pm |
|
|
Here's a picture of one installed on a flywheel from somewhere on the internet.
Note that the holes you'd be cutting through would be the bigger diameter holes a little farther out on the other side of the ears, but also note that where it's cutis right at the edge of the flywheel, yours would have been in a little bit. I still think the pictures are one of the front and one of the backside, but it doesn't matter, you know where to cut and which holes to use. They're 5/16 diameter.
 |
||
|
||
|
Hysteria
Groupie
Joined: May-31-2020 Location: Indiana Status: Offline Points: 70 |
Post Options
Thanks(0)
Quote Reply
Posted: May-21-2021 at 9:11pm |
|
|
Perfect, thank you. I'm going to scribe a new line with a little more material left since it appears there is enough space.
You were right about the photo being flipped, I mistakenly thought that you had drawn on the same photo that was in the original post, which matched the photo I took of my damper. |
||
|
||
|
Post Reply
|
|
Tweet
|
| Forum Jump | Forum Permissions You cannot post new topics in this forum You cannot reply to topics in this forum You cannot delete your posts in this forum You cannot edit your posts in this forum You cannot create polls in this forum You cannot vote in polls in this forum |
Topic Options
KENO wrote:
