Boats For Sale:
PCM rear mount rubber |
Post Reply 
|
| Author | |
MourningWood 
Gold Member 
Joined: June-13-2014 Location: NorCal Status: Offline Points: 917 |
 Post Options
 Thanks(0)
 Quote Reply
 Topic: PCM rear mount rubberPosted: November-29-2021 at 6:39pm |
|
The large, lower rubber bushing (w/ metal insert)...........
How in the f(^#@$^*(^$ do you get it into the mount? Thanks
|
|
|
1964 Dunphy X-55 "One 'N Dun"
'I measured twice, cut three times, and it's still too short!" |
|
 |
|
|
Hollywood
Moderator Group
Joined: February-04-2004 Location: Twin Lakes, WI Status: Offline Points: 13515 |
Post Options
Thanks(0)
Quote Reply
Posted: November-29-2021 at 8:46pm |
|
I left mine in the freezer for a few days before even starting, then I used plenty of silicone grease, a big bolt, nut & washers as a puller. Oh, and a big impact driver.
Pounding them in just caused heat build up and a mushroom effect half way through. Big failure. |
|
|
|
|
Wilhelm Hertzog
Senior Member 
Joined: June-14-2014 Location: Cape Town Status: Offline Points: 334 |
Post Options
Thanks(0)
Quote Reply
Posted: November-30-2021 at 5:58pm |
|
I lubed mine up with water soluble lubricant and then pressed it in using a bench vice.
|
|
|
1982 Ski Nautique PCM351W RR II Velvet Drive 10-17-003 1:1 II PerfectPass Stargazer
Do not go gentle into that good night. Rage, rage against the dying of the light. |
|
|
|
|
MourningWood
Gold Member
Joined: June-13-2014 Location: NorCal Status: Offline Points: 917 |
Post Options
Thanks(0)
Quote Reply
Posted: December-07-2021 at 10:17am |
|
"water soluble lubricant"?
Hey Honey?........
|
|
|
1964 Dunphy X-55 "One 'N Dun"
'I measured twice, cut three times, and it's still too short!" |
|
|
|
|
Wilhelm Hertzog
Senior Member
Joined: June-14-2014 Location: Cape Town Status: Offline Points: 334 |
Post Options
Thanks(0)
Quote Reply
Posted: December-07-2021 at 11:18am |
|
Exactly.
|
|
|
1982 Ski Nautique PCM351W RR II Velvet Drive 10-17-003 1:1 II PerfectPass Stargazer
Do not go gentle into that good night. Rage, rage against the dying of the light. |
|
|
|
|
MourningWood
Gold Member
Joined: June-13-2014 Location: NorCal Status: Offline Points: 917 |
Post Options
Thanks(0)
Quote Reply
Posted: December-07-2021 at 4:15pm |
and yet, I came up with so, so much more.....
|
|
|
1964 Dunphy X-55 "One 'N Dun"
'I measured twice, cut three times, and it's still too short!" |
|
|
|
|
MourningWood
Gold Member
Joined: June-13-2014 Location: NorCal Status: Offline Points: 917 |
Post Options
Thanks(0)
Quote Reply
Posted: December-07-2021 at 4:17pm |
|
Good news is I got a new bushing. This after trying to press out the inner metal sleeve which I thought might be stuck inside, and thus destroying the bushing. The new one went right in w/ a bit of silicone spray and light shop press pressure. Thanks all...
|
|
|
1964 Dunphy X-55 "One 'N Dun"
'I measured twice, cut three times, and it's still too short!" |
|
|
|
|
Post Reply
|
|
Tweet
|
| Forum Jump | Forum Permissions You cannot post new topics in this forum You cannot reply to topics in this forum You cannot delete your posts in this forum You cannot edit your posts in this forum You cannot create polls in this forum You cannot vote in polls in this forum |
Topic Options
Wilhelm Hertzog wrote: