Isolater Bushing Transmission Mount |
Post Reply ![]() |
Author | ||
marksa1458 ![]() Newbie ![]() Joined: April-15-2009 Location: Webster, MA Status: Offline Points: 30 |
![]() ![]() ![]() ![]() ![]() Posted: October-11-2022 at 2:31pm |
|
Was winterizing a new to me 2000 Ski Nautique with the PCM 5.8 HO engine. The driver's side transmission Isolater bushing has worked its way out of the mount:
![]() ![]() ![]() What is the repair for this? I can order just the bushing from Ski Dim or I can order a whole new Transmission mount - There is no vibration in the driveline at any speed/rpm and there is no movement on the mount if throttle is applied. The passenger side mount looks like this: ![]() Thanks |
||
![]() |
||
Gary S ![]() Grand Poobah ![]() ![]() Joined: November-30-2006 Location: Illinois Status: Offline Points: 14096 |
![]() ![]() ![]() ![]() ![]() |
|
Skidim does have the parts but you'll have to call them they are not listed. The rubber part is called an isolator PCM part number R094004 and lists for like 3.00. And it looks like your missing the clip. Snap ring R017032 thats under a 1.00. Might be a good idea to check your alignment when your all through as well something has shifted.
|
||
![]() |
||
marksa1458 ![]() Newbie ![]() Joined: April-15-2009 Location: Webster, MA Status: Offline Points: 30 |
![]() ![]() ![]() ![]() ![]() |
|
Thanks for the quick reply - I will reach out to SkiDim and get the parts ordered.
So - *loosen the trunion bolts *reposition the mount *install the new bushing and clip *Tighten the Trunion bolts *Alignment *Go Skiing Is that right?
|
||
![]() |
||
KENO ![]() Grand Poobah ![]() Joined: June-06-2004 Location: United States Status: Offline Points: 11247 |
![]() ![]() ![]() ![]() ![]() |
|
![]() |
||
marksa1458 ![]() Newbie ![]() Joined: April-15-2009 Location: Webster, MA Status: Offline Points: 30 |
![]() ![]() ![]() ![]() ![]() |
|
I ordered them! Appreciate the part numbers
|
||
![]() |
||
MourningWood ![]() Gold Member ![]() Joined: June-13-2014 Location: NorCal Status: Offline Points: 920 |
![]() ![]() ![]() ![]() ![]() |
|
Recently did this job on a '94-same mount. Much, much easier with the entire mount out of the boat and on a workbench. Winter is coming-you have the time...
|
||
1964 Dunphy X-55 "One 'N Dun"
'I measured twice, cut three times, and it's still too short!" |
||
![]() |
||
Gary S ![]() Grand Poobah ![]() ![]() Joined: November-30-2006 Location: Illinois Status: Offline Points: 14096 |
![]() ![]() ![]() ![]() ![]() |
|
Now Ken I knew they had them and even looked- but nothing came up. Did you search by part number? As long as you know what you want or even have PCM's part number they can order since they are a PCM dealer.
|
||
![]() |
||
KENO ![]() Grand Poobah ![]() Joined: June-06-2004 Location: United States Status: Offline Points: 11247 |
![]() ![]() ![]() ![]() ![]() |
|
At the top of about every page on their website it says "what part do you need today?" I put the PCM part number in there
|
||
![]() |
||
Gary S ![]() Grand Poobah ![]() ![]() Joined: November-30-2006 Location: Illinois Status: Offline Points: 14096 |
![]() ![]() ![]() ![]() ![]() |
|
Always learning Thanks. Didn't realize you could put in part numbers- probably one of the updates to their site when they upgraded. Now help me find a manual or parts diagram for an Indmar 140
![]() |
||
![]() |
||
KENO ![]() Grand Poobah ![]() Joined: June-06-2004 Location: United States Status: Offline Points: 11247 |
![]() ![]() ![]() ![]() ![]() |
|
I keep hearing the theme song from Mission Impossible in my head, but I can try
![]() |
||
![]() |
||
Gary S ![]() Grand Poobah ![]() ![]() Joined: November-30-2006 Location: Illinois Status: Offline Points: 14096 |
![]() ![]() ![]() ![]() ![]() |
|
At least your getting a song Ken - all I have is my tape on fire as it self destructs
![]() |
||
![]() |
Post Reply ![]() |
|
Tweet
|
Forum Jump | Forum Permissions ![]() You cannot post new topics in this forum You cannot reply to topics in this forum You cannot delete your posts in this forum You cannot edit your posts in this forum You cannot create polls in this forum You cannot vote in polls in this forum |