91 nautique excel will not throttle up under load |
Post Reply | Page <12 |
Author | |
Shua4242
Newbie Joined: June-24-2018 Location: 45880 Status: Offline Points: 28 |
Post Options
Thanks(0)
|
My sender does not work, so I will measure and order that one ou are talking about, and okay, I will pull that out and check and clean it, as it is the only thing I have not had apart or new for the fuel system. I will do this tomorrow night and let you know.
|
|
Air206
Grand Poobah Joined: September-28-2008 Location: Roanoke, VA Status: Offline Points: 3000 |
Post Options
Thanks(0)
|
Years ago, I worked out a CCFan discount 20% - It may be worth asking. You go directly to WEMA............ If not, at least ask for free shipping.
|
|
Air206
Grand Poobah Joined: September-28-2008 Location: Roanoke, VA Status: Offline Points: 3000 |
Post Options
Thanks(0)
|
Wish you were closer, I'd help you. Always good to meet an Excel brother.
Ft. Wayne area, right? |
|
Shua4242
Newbie Joined: June-24-2018 Location: 45880 Status: Offline Points: 28 |
Post Options
Thanks(0)
|
Yes, I live in Ohio but right on the state line of Fort Wayne, Indiana
|
|
Shua4242
Newbie Joined: June-24-2018 Location: 45880 Status: Offline Points: 28 |
Post Options
Thanks(0)
|
I believe my anti siphon valve is the culprit, I could not blew through it with my mouth, How hard are these supposed to be? I will get a new one tomorrow and take it to water to find out.
|
|
KENO
Grand Poobah Joined: June-06-2004 Location: United States Status: Offline Points: 11061 |
Post Options
Thanks(0)
|
I have a new one on the workbench and I couldn't blow hard enough to unseat the ball. If you take a little screwdriver and push on the ball, it should move very easily and the spring will reseat the ball when you remove the screwdriver. A little hard to quantify "real easy" but hardly any force is required at all |
|
Shua4242
Newbie Joined: June-24-2018 Location: 45880 Status: Offline Points: 28 |
Post Options
Thanks(0)
|
That is how mine acted, easy with a screw driver but hard to blow, I am going to try the new coil on the water tomorrow and I will post back on how the trip went.
|
|
Shua4242
Newbie Joined: June-24-2018 Location: 45880 Status: Offline Points: 28 |
Post Options
Thanks(0)
|
Well thanks for all the hep guys, I finally have a boat. The engine wasnt running right because of a fuel problem, I believe it was the anti siphon valve as it was dirty. But I did also change the fuel filter so it could of been that. The tranny issue was the previous owner had the linkage on the tranny wrong, when it was in gear, the pump was not working. I will create a new thread on how I swapped an 89 truck engine into a reverse rotation boat engine since I know know my problem was only fuel.
|
|
rosconole
Gold Member Joined: May-10-2008 Location: United States Status: Offline Points: 759 |
Post Options
Thanks(0)
|
Did you get the leaky trans issue figured out sounded like it was over filled.... or loose hose
|
|
1989 ski nautique ,1991 barefoot nautique, 1993 Mustang Cobra 1998 5.0 Magazine shootout invitee
|
|
Post Reply | Page <12 |
Tweet
|
Forum Jump | Forum Permissions You cannot post new topics in this forum You cannot reply to topics in this forum You cannot delete your posts in this forum You cannot edit your posts in this forum You cannot create polls in this forum You cannot vote in polls in this forum |