2001 Transmission Fluid Change
Printed From: CorrectCraftFan.com
Category: Repairs and Maintenance
Forum Name: Boat Maintenance
Forum Discription: Discuss maintenance of your Correct Craft
URL: http://www.CorrectCraftFan.com/forum/forum_posts.asp?TID=11209
Printed Date: November-17-2024 at 5:07am
Topic: 2001 Transmission Fluid Change
Posted By: tjamesbo
Subject: 2001 Transmission Fluid Change
Date Posted: July-14-2008 at 11:01am
|
Going to Change my Tranny Fluid and am looking at draining it out by pulling the bottom hose that runs up to the cooler only question is do i pull the right angle connector out or just the hose ( see piccie ) seemsto me the whole connector should come out in order to get the maimum drain? also the manual mentions some kind of Strainer in there it looks small anything to watch out for ???
I must admit I'm also tempted to disconect hose at the cooler and pump it out what are the pros and cons of either ??? How do I upload a piccie ??? Greetings from the cold and wet UK where the weather can only get better!!!! |
Replies:
Posted By: tjamesbo
Date Posted: July-14-2008 at 12:34pm
here is the picture of hose bottom undo the hose and rotate the angle connector or remove it ??? |
Posted By: 88 Nautique
Date Posted: July-14-2008 at 12:37pm
|
A lot of us here just pump it out of the filler. I didn't heve a pump the first time I did it but I had a large syringe, (30cc). Hooked some tubing to it and sucked it out. Took a while but I was able to empty it pretty good.
For posting pictures, here's a good link: http://www.correctcraftfan.com/forum/forum_posts.asp?TID=5142&KW=photobucket - Posting Photo's Kurt ------------- http://www.correctcraftfan.com/diaries/details.asp?ID=1657" rel="nofollow - My 88 Nautique |
Posted By: behindpropeller
Date Posted: July-14-2008 at 2:25pm
|
Looks like some cleaning is in order before you start your fluid changing project. ------------- |
Posted By: 74SkiNautique
Date Posted: August-05-2008 at 9:37pm
|
hey...I use a pump. I got mine out of an overtons catalog. I have a B/W 1:1. Just stick it in the filler and you should be able to get most of it out!
http://www.overtons.com/modperl/product/details.cgi?i=71783&pdesc=Hand_Bilge_Pump&str=hand%20pump&merchID=1008&r=view Something like this should do it. ------------- 74SkiNautique |
Posted By: Sam B
Date Posted: August-06-2008 at 11:07am
|
I bought a simer drillmaster pump some fittings and hose then good to go.
Maximum pumping capacity up to 225 gallons per hour It's multi-purpose ability allows it to pump water or change oil in lawn mowers, boats and cars. Minimum drill speed 1200 RPM Model CM10 - 1200 RPM Check out Simerpumps.com Hope this helps Sam ------------- Loud pipes save lives!! 2011 Green Lake Reunion Best of Show. %20http://www.correctcraftfan.com/diaries/details.asp?ID=3391&sort=&pagenum=3&yrstart=1973&yrend=1973" rel="nofollow - Sam's 73 |
Posted By: Hollywood
Date Posted: August-06-2008 at 12:24pm
|
Careful not to let the hose fall off the end of the hand pump into the case. ------------- |
Posted By: hunterdan
Date Posted: August-06-2008 at 1:03pm
|
how much oil do you put in. For the 1:23 what oil do you use?? ------------- Dan |