Are there any Fish Nautique NOS parts out there?
Printed From: CorrectCraftFan.com
Category: Buy and Sell
Forum Name: Boat Parts Wanted
Forum Discription: Parts wanted only
URL: http://www.CorrectCraftFan.com/forum/forum_posts.asp?TID=23768
Printed Date: November-17-2024 at 11:31pm
Topic: Are there any Fish Nautique NOS parts out there?
Posted By: dvrdave
Subject: Are there any Fish Nautique NOS parts out there?
Date Posted: October-08-2011 at 2:41am
|
Ok I finally got the original console for my boat, but it has been sitting out in the weather for years and needs to be restored. I would like to find anyone in the central fl area that has NOS parts for the Fish Nautiques, stuff like teak parts, panels, hardware, etc. I know the teak can be copied, and most other parts do not have to be "original NOS", but I am finally going to start prepping the hull to get the motor put back in and I am starting with a completely stripped engine bay that someone else took apart, and there is no instruction diagram to go on so I can lay things out the way I want, but would prefer to make it as original as possible.
Thanks, Dave ------------- Diver Dave |
Replies:
Posted By: N3BOATWORKS
Date Posted: October-10-2011 at 1:50pm
|
I have a US coast guard original plate if you needed one. ------------- RYAN N3BOATWORKS PARTS MANAGER |
Posted By: dvrdave
Date Posted: October-10-2011 at 2:25pm
|
I just might need one, but I have not looked for the original one on the console as of yet so I do not know for sure. We had a tree go down with all the weather so I am not working on the boat for the next few days. I will have find out though and let you know.
Thanks, -Dave ------------- Diver Dave |
Posted By: N3BOATWORKS
Date Posted: October-10-2011 at 6:01pm
|
That is fine.I have a few in stock so just let me know.
------------- RYAN N3BOATWORKS PARTS MANAGER |
Posted By: LarryD
Date Posted: January-31-2012 at 7:01pm
|
Hello N3BOATWORKS. I am interested in a US CoastGuard Original Load Capacity Plate for a 1987 Fish Nautique. DO you still have one?
Thanks. ------------- LarryD |
Posted By: LarryD
Date Posted: June-06-2012 at 6:37pm
|
Hello N3BOATWORKS. I am interested in a US CoastGuard Original Load Capacity Plate for a 1987 Fish Nautique. DO you still have one? Thanks. LD ------------- LarryD |
Posted By: 69barri
Date Posted: June-06-2012 at 7:59pm
|
I have a trailer with new axles, disc brakes, and new bunks that was under my Cuddy Nautique if you are interested. ------------- 1963 Debonnaire Deluxe 1972 Separator Jet Boat |
Posted By: dvrdave
Date Posted: June-07-2012 at 12:50am
|
Hey this is Dave, I am the one that started this thread, but it is getting kind of old at this point. I am still working on the boat but I am also trying to sell it. I have it on a pretty good trailer, but the rudder is a little close to the ground so a proper trailer might make it easier for me to work on, and easier to sell so I would like to find out more about it. First I would need to know if you are in central Florida, and if so and you have pics please email them to me directly at dvrdave@hotmail.com ------------- Diver Dave |
Posted By: 69barri
Date Posted: June-15-2012 at 8:40pm
I am currently located in Atlanta, GA but the trailer is in Mount Dora. This is the only picture that I have right now from when I transported my Cuddy Nautique down from Connecticut. The shop where my trailer is located will be sending me pictures next week. This picture was taken before I redid everything. Hope this helps.  ------------- 1963 Debonnaire Deluxe 1972 Separator Jet Boat |
Posted By: dvrdave
Date Posted: June-16-2012 at 1:35am
|
Mount Dora is not too far from here, and if you can get some pics of the cross members and axles with the boat off of it that would probably show me enough about its condition to get me in the truck to drive up there to check it out in person. -Dave ------------- Diver Dave |