Impeller
Printed From: CorrectCraftFan.com
Category: General Correct Craft Discussion
Forum Name: General Discussion
Forum Discription: Anything Correct Craft
URL: http://www.CorrectCraftFan.com/forum/forum_posts.asp?TID=49847
Printed Date: March-04-2025 at 5:11am
Topic: Impeller
Posted By: wsavini
Subject: Impeller
Date Posted: May-26-2021 at 11:54pm
| Hi all, looking for info on a Sherwood pump. Old, on a 1965 cc Mustang Ford 260. I need a new impeller. |
Replies:
Posted By: KENO
Date Posted: May-27-2021 at 6:12am
Looking for info, one of these things in the link might come in handy  http://docplayer.net/15000906-Maintenance-repair-manual.html" rel="nofollow - http://docplayer.net/15000906-Maintenance-repair-manual.html" rel="nofollow - link
|
Posted By: 8122pbrainard
Date Posted: May-27-2021 at 6:27am
|
Wayne, Here's the chart showing the common Sherwood impellers. Without the exact pump model you have take a look and see if you can match up some dimensions.  With the part number, you can then go shopping. Here's a start but there's probably a less cost out there. https://www.jamestowndistributors.com/product/product-detail/8374" rel="nofollow - Sherwood Replacement Impellers (jamestowndistributors.com) The Jamestown link will also get you to more details like the bore and it's type. ------------- /diaries/details.asp?ID=1622" rel="nofollow - 54 Atom /diaries/details.asp?ID=2179" rel="nofollow - 77 Tique 64 X55 Dunphy Keep it original, Pete < |
Posted By: KENO
Date Posted: May-27-2021 at 7:11am
|
And here's a link to an old thread, he had a 65 Mustang with a 260 and gave his pump part number, then it was easy to come up with an impeller number. Yours might be the same.........maybe http://www.correctcraftfan.com/forum/forum_posts.asp?TID=47874&title=1965-mustang-water-pump-impeller-replacment" rel="nofollow - link It's not a common one and it's pretty expensive too Here's one place to find one if that's what you need http://www.go2marine.com/Sherwood-Impeller-10187-9-Blades" rel="nofollow - link
|
Posted By: 8122pbrainard
Date Posted: May-27-2021 at 8:12am
|
Wayne, When you open up the pump, look for a model number on the housing face where the gasket goes. Many of the Sherwood pumps were stamped there. Cooling issues this year or are you just swapping the impeller for good practice?
------------- /diaries/details.asp?ID=1622" rel="nofollow - 54 Atom /diaries/details.asp?ID=2179" rel="nofollow - 77 Tique 64 X55 Dunphy Keep it original, Pete < |
Posted By: Nautiquehunter
Date Posted: May-27-2021 at 8:49am
| Make sure you get a genuine Sherwood impeller . There are a lot of aftermarket impellers out there , They look the same but don't pump the same. I just went through a month of cooling issues on the 67 Mustang only to find out the Globe run dry impeller was the problem all along. |
Posted By: wsavini
Date Posted: May-27-2021 at 9:13am
| No cooling issues but After searching around I couldn’t locate the impeller so I asked the owner of Marine engines in Holliston,Ma. I showed him the pump and impeller. He said he could find one and he took the old one to compare. He wasn’t able to find one and the old one got lost in the shuffle. But it was in tough shape. Number stamped in 010785G then below that it has a V 4 . |
Posted By: KENO
Date Posted: May-27-2021 at 9:23am
|
It takes the same 10187 impeller linked earlier in the thread (in my last post.) Just think, if you gave that info in post #1, it would have been so much easier
|
Posted By: wsavini
Date Posted: May-27-2021 at 9:31am
|
Sorry, Didn t have it handy. Posted at midnight. |
Posted By: wsavini
Date Posted: May-27-2021 at 10:22am
| Ok I ordered a 10187. Thank you all for your help. If I could figure out how to post pics on here I could show you how worn the inside of the pump is. I noticed the newer stuff 70’s up have rebuild kits. But don’t see anything close to what mine looks like. |