318 raw water pump
Printed From: CorrectCraftFan.com
Category: Buy and Sell
Forum Name: Boat Parts Wanted
Forum Discription: Parts wanted only
URL: http://www.CorrectCraftFan.com/forum/forum_posts.asp?TID=50530
Printed Date: November-23-2024 at 8:29pm
Topic: 318 raw water pump
Posted By: ScottZ
Subject: 318 raw water pump
Date Posted: March-28-2022 at 3:11pm
|
Does anyone out there have a good used or new raw water pump for a 318 Chrysler? I do not think there are manufactured any longer. Thanks. ------------- Scott Zuelzke Lake Mitchell , AL 1984 Ski Nautique 1972 Skier |
Replies:
Posted By: 67 ski nat
Date Posted: March-28-2022 at 3:57pm
|
I see couple on eBay $600. I’ve seen in past for $400 But if you have the 2 halves of brass body You can rebuild entire unit with every component for 175 (quality kit) Kit has bearing, seals, impeller, rear bushing Tip, there is a brass washer that goes in cavity first before spring seal, very important |
Posted By: ScottZ
Date Posted: March-28-2022 at 4:05pm
|
The pump I have has a slow drip. Where would you get the rebuild kit from? ------------- Scott Zuelzke Lake Mitchell , AL 1984 Ski Nautique 1972 Skier |
Posted By: 67 ski nat
Date Posted: March-28-2022 at 4:09pm
| I’ll get the info tonight when I get home |
Posted By: 67 ski nat
Date Posted: March-28-2022 at 7:11pm
|
Steve butrick 850-380-1731 Pump shop in Florida |
Posted By: 67 ski nat
Date Posted: March-28-2022 at 7:21pm
|
I’ve used 2 kits and rebuilt brass body D-65 double pockets Very nice kit high quality pieces, USA made I found a old core on eBay $75 rebuilt it works flawlessly. Pay attention to detail and all surfaces smooth |
Posted By: TRBenj
Date Posted: March-28-2022 at 8:35pm
| You may want to be more specific on the year, or reference the pump by its number (or post a pic). Chrysler used a few different ones. |
Posted By: 67 ski nat
Date Posted: March-29-2022 at 8:27am
| Good point. I have and refer to the d60 d65 double pocket with 1” in/out and 5/8 shaft. Number should be stamped on pump under pulley where shaft exits |
Posted By: ScottZ
Date Posted: March-29-2022 at 5:21pm
|
This is the only pump I have ever dealt with for the 318. It uses the Sherwood 09959-K impellers. This one is working but has a small drip off the front half of the pump.  
------------- Scott Zuelzke Lake Mitchell , AL 1984 Ski Nautique 1972 Skier |
Posted By: ScottZ
Date Posted: March-29-2022 at 5:23pm
|
This engine is out of a 1972 Ski Nautique. I do not have the pump in hand to check the number. ------------- Scott Zuelzke Lake Mitchell , AL 1984 Ski Nautique 1972 Skier |
Posted By: ScottZ
Date Posted: March-29-2022 at 5:25pm
|
Daryn, I will pass the info. on to the people who have the engine. Thanks for your help. ------------- Scott Zuelzke Lake Mitchell , AL 1984 Ski Nautique 1972 Skier |
Posted By: 67 ski nat
Date Posted: March-30-2022 at 9:33am
|
Wow. Your pump and engine look super clean and nice Yes your impeller numbers are correct 9959. Kit comes with those too Sounds like you have a d-65 Sherwood pump. Good luck |
Posted By: ScottZ
Date Posted: March-30-2022 at 10:08am
|
This is a fresh engine. Reman Jasper long block. Previous block was bad. Orange 72 Promo being rebuilt too. This is the same engine I had in my 71 Ski Nautique. ------------- Scott Zuelzke Lake Mitchell , AL 1984 Ski Nautique 1972 Skier |
Posted By: 67 ski nat
Date Posted: March-30-2022 at 3:18pm
|
Good to know you went jasper I’ve been looking at many brands too I’ll take another look at jasper Your doing nice job |