small block ford raw water pump
Printed From: CorrectCraftFan.com
Category: Buy and Sell
Forum Name: Boat Parts Wanted
Forum Discription: Parts wanted only
URL: http://www.CorrectCraftFan.com/forum/forum_posts.asp?TID=50541
Printed Date: November-23-2024 at 8:23pm
Topic: small block ford raw water pump
Posted By: sbford
Subject: small block ford raw water pump
Date Posted: April-04-2022 at 10:51am
| Looking for the raw water pump assembly for a small block ford, 260-289 |
Replies:
Posted By: KENO
Date Posted: April-04-2022 at 2:09pm
|
A couple of things you should mention if you want to get the right part would be What was the marinization of the engine? maybe Interceptor for example Who made the pump? maybe Sherwood for example Are there any numbers on the pump? maybe something like S11090G for example Do you really need the whole pump or just some parts? OK, so I can't count and that's more than a couple of questions
 |
Posted By: sbford
Date Posted: April-04-2022 at 5:31pm
| interceptor engine, I was told it could have been a jabsco or sherwood need the assembly, cover plate that goes where the auto water pump would go and the raw water pump and the brackets that fasten the pump to the engine |
Posted By: KENO
Date Posted: April-04-2022 at 8:33pm
|
Some of the Interceptor SBF's used a circ pump and some early ones had the block off plate. They had different raw water pumps and brackets Hopefully somebody reads your post and has the parts you need
|
Posted By: Nautiquehunter
Date Posted: April-05-2022 at 7:03am
|
I might have one off a 67 289. I will look. |
Posted By: sbford
Date Posted: April-05-2022 at 9:53am
| Great hope you find it |
Posted By: swilliams
Date Posted: April-05-2022 at 10:37am
|
Perhaps some pics of your engine would help. ------------- 1976 Martinique,350 Omc. 1975 Glastron/Carlson CV16,115 Merc. |
Posted By: sbford
Date Posted: May-12-2022 at 11:25am
Posted By: sbford
Date Posted: May-12-2022 at 11:28am
| need the two Ts that separate the water at the raw water pump and then up across from the exhaust manifolds |
Posted By: Gary S
Date Posted: May-12-2022 at 12:02pm
|
Pictures? Lots of times many of us can figure out a substitute if we know just what your looking for. For instance could you make them up from a copper pipe T? ------------- http://www.correctcraftfan.com/diaries/details.asp?ID=1711&sort=&pagenum=1&yrstart=1966&yrend=1970" rel="nofollow - 69 Mustang HM SS 95 Nautique Super Sport |
Posted By: sbford
Date Posted: May-12-2022 at 2:52pm
|
Posted By: sbford
Date Posted: May-12-2022 at 2:57pm
| This is a picture of an engine from a lyman same set up as mine raw water pump to the T then auto water pump and up to the T at the exhaust risers |
Posted By: TRBenj
Date Posted: May-12-2022 at 2:59pm
| Is that your pump or just one like you need? Obviously they’re rebuildable. That one’s a Sherwood, though I don’t know the model #. |
Posted By: KENO
Date Posted: May-12-2022 at 6:14pm
| Do you still need the pump like mentioned a while back in the first post or did you get one and just need fittings now? |
Posted By: sbford
Date Posted: May-12-2022 at 6:27pm
| found the sherwood pump just need the fittings Ts or at least the sizes of the fittings Ts because I suspect they are not all the same diameter openings. It would be nice if they were all 1" or 3/4" but I would guess they have different diameter opening in each T. |
Posted By: KENO
Date Posted: May-12-2022 at 6:31pm
|
I suppose if you know the number of the pump and posted it here, it would make the thread more useful for somebody in the future with the same problem.
|