Trailer Maintenance
Printed From: CorrectCraftFan.com
Category: Repairs and Maintenance
Forum Name: Boat Maintenance
Forum Discription: Discuss maintenance of your Correct Craft
URL: http://www.CorrectCraftFan.com/forum/forum_posts.asp?TID=7467
Printed Date: September-24-2024 at 2:47pm
Topic: Trailer Maintenance
Posted By: joelhern2
Subject: Trailer Maintenance
Date Posted: July-11-2007 at 3:55pm
|
I pump my trailer hubs with grease when needed and especially before long trips. However, recently the grease slings itself all over the outside of the tires and wheels....whats this all about?
I know that Im not over greasing them, because I cut off the grease right when I see water emerge (just like the directions read). Any other routine maintenance advice for a 1991 trailer? Thanks in advance... ------------- http://www.correctcraftfan.com/diaries/details.asp?ID=1479&sort=&pagenum=1&yrstart=1991&yrend=1995 - '91 Barefoot Nautique |
Replies:
Posted By: bmiller
Date Posted: July-11-2007 at 5:00pm
| Your grease seals on the back of the hub are bad.Also when you take the hub off,look at the axle for any groove marks on the shaft.This will also cause the grease seals not to mate properly to the axle,causing your grease slinging.Some bearing places will sell a sleave to put over the section of bad axle if you do have a groove in it.Really you should only have to put grease in your hub once a year as long as you have your bearing packed properly from the start.My advise is to replace the seals and repack the bearings properly.Your bubby bearings are spring loaded so once you replace the seals and pack the bearing,just add enough grease till the front of the bubby bearing bottoms out the front.Also make sure you use marine grade bearing grease. |
Posted By: 87BFN owner
Date Posted: July-12-2007 at 12:09am
|
I use molloy grease seems to work better then regular hi-temp grease. ------------- |
Posted By: SkiBum
Date Posted: July-12-2007 at 12:44am
|
Used to have the same problem. Replaced the seals in the back and repacked the bearings with that red colored grease. Now I just pump enough grease in to make the bearing buddy start to float. I have hose clamps on the rubber outer caps to help keep out water. ------------- Bill http://www.freewebs.com/billsboatworks - http://www.freewebs.com/billsboatworks www.freewebs.com/billsboatworks 1987 SN Rebuild Project |
Posted By: David F
Date Posted: July-12-2007 at 12:19pm
|
Hose clamps on the rubber caps...I like it! Kind of gheto, but good idea. I tend to loose them most of all, so that might help them stay put. I suppose that out of balance hose clamp is too close to the center of the wheel to make any difference. ------------- |
Posted By: 8122pbrainard
Date Posted: July-12-2007 at 12:29pm
|
I like Bills idea that he only pumps enough to just start the sping loaded plunger to float. If you fill them then I think with the heat and pressure, is blows past the inside seal. I just washed off the splattered grease from the inside of the wheel on one side of my Atom trailer. It did it with less than 200 miles and that was with brand new spindles and hubs!! ------------- /diaries/details.asp?ID=1622" rel="nofollow - 54 Atom /diaries/details.asp?ID=2179" rel="nofollow - 77 Tique 64 X55 Dunphy Keep it original, Pete < |
Posted By: David F
Date Posted: July-12-2007 at 1:14pm
|
Well, it is not Bill's idea, but the correct way to do it. The instructions on new bearing buddies tell you to do it just that way. Just enough grease to unseat the spring loaded cap. ------------- |
Posted By: Darrel
Date Posted: July-12-2007 at 3:49pm
| Back in the day when we lost a rubber cap we would cut a Coors Light can in half and duct tape it on. That was pretty ghetto. Disclaimer: it was not a Nautique, it was 73 Thunderbird Tri hull with a Johnson 135 OB. My brother and I installed a center pull pylon on it and painted "Nontique 2002" on the side. |
Posted By: BuffaloBFN
Date Posted: July-12-2007 at 4:31pm
|
LMAO ------------- http://correctcraftfan.com/diaries/details.asp?ID=2331&sort=&pagenum=12&yrstart=1986&yrend=1990" rel="nofollow - 1988 BFN-sold "It's a Livin' Thing...What a Terrible Thing to Lose" ELO |
Posted By: JAG459
Date Posted: July-12-2007 at 11:42pm
| I agree with bmiller When I replace the seals on my trailer I installed the seal savers available from Bearing Buddie www.bearingbuddy.com. and I haven't had a problem since. |
Posted By: 8122pbrainard
Date Posted: July-13-2007 at 10:01am
I took a look at the seal savers and will need to put some on my trailers. Looks like a nice upgrade on the seal plus has a O ring backup. Like I said, I had less than 200 miles on new spindles and seals when one of them started throwing grease. Of coarse the spindles are probably made in China and they have no idea of the RMS surface finish requirements for a seal and any tolerence you put on a print they ignore anyway!! David, While I was at the bearing buddy site I took a look at the greasing instructions. It's funny because under the frequently asked questions they tell you to compleatly fill them up but in the install section they tell you to put in enough grease to only float the spring loaded piston a 1/8" !! ------------- /diaries/details.asp?ID=1622" rel="nofollow - 54 Atom /diaries/details.asp?ID=2179" rel="nofollow - 77 Tique 64 X55 Dunphy Keep it original, Pete < |
JAG459 wrote:Posted By: jdkenyon
Date Posted: July-13-2007 at 3:04pm
|
When I replaced the seals on my trailer I took the old ones to a local bearing place and asked for a double lip seal. My dad swears by these and they definitely look much more substantial for holding up. They were a little more money but if it saves a mess of grease on the brakes I am all for it. ------------- http://www.correctcraftfan.com/diaries/details.asp?ID=1955 - 94 Ski Nautique |
Posted By: David F
Date Posted: July-13-2007 at 3:19pm
Excellent point and reminder. Double lip seals are crucial with boat trailers. Standard seals are designed to keep the grease in, not the water out. Double lip seals do both. ------------- |