Damper Plate |
Post Reply | Page <12 |
Author | |
nitro scott
Newbie Joined: September-02-2019 Location: crosby Status: Offline Points: 8 |
Post Options
Thanks(0)
|
Is there an automotive application for a damper? Are they easy to get. Mine is looking a little worn.
|
|
1973 Ski Nautique Tow boat
|
|
KENO
Grand Poobah Joined: June-06-2004 Location: United States Status: Offline Points: 10753 |
Post Options
Thanks(0)
|
So now you get around to mentioning something else that was done at the same time like a carburetor kit that maybe should have been mentioned in the first post Easy enough to have a rough running engine due to some carburetor issues. Not knowing what this "roughness " is like without being there, I think I'd be looking at the rebuild job on the carburetor if the flywheel is the correct 28 oz imbalance |
|
KENO
Grand Poobah Joined: June-06-2004 Location: United States Status: Offline Points: 10753 |
Post Options
Thanks(0)
|
28 oz. |
|
schultz227
Groupie Joined: August-20-2019 Location: Indiana Status: Offline Points: 49 |
Post Options
Thanks(0)
|
Does it take the 28oz ? Or 50 ?
|
|
Gary S
Grand Poobah Joined: November-30-2006 Location: Illinois Status: Offline Points: 14096 |
Post Options
Thanks(0)
|
What I'm thinking and I suspect Ken too is that the wrong flywheel may have been used. Fords are externally balanced- there are two different imbalances 28 oz and a 50 oz,so a flywheel part number if/when you can get it would help.
|
|
schultz227
Groupie Joined: August-20-2019 Location: Indiana Status: Offline Points: 49 |
Post Options
Thanks(0)
|
So in review he put a carb kit on , new flywheel not just ring gear , rear main seal, damper plate .. and starter ... ran beautifully before all this except for the starting issue and carb leak but it ran smooth
|
|
schultz227
Groupie Joined: August-20-2019 Location: Indiana Status: Offline Points: 49 |
Post Options
Thanks(0)
|
Friend of mine did the damper plate on his 88 and says it was the same thing with the bad vibration and he got what he called a Sachs plate and it was better ..
|
|
schultz227
Groupie Joined: August-20-2019 Location: Indiana Status: Offline Points: 49 |
Post Options
Thanks(0)
|
He’s telling me it can’t be the damper plate because it all was installed as it came off in the same bolt pattern or whatever as the old one . He did put a carb kit on it as I had a major leak at the accelerator pump
|
|
8122pbrainard
Grand Poobah Joined: September-14-2006 Location: Three Lakes Wi. Status: Offline Points: 41040 |
Post Options
Thanks(0)
|
Kyle, What's he saying about the problem? |
|
schultz227
Groupie Joined: August-20-2019 Location: Indiana Status: Offline Points: 49 |
Post Options
Thanks(0)
|
Don’t have it , mechanic has it and not responding tonight
|
|
KENO
Grand Poobah Joined: June-06-2004 Location: United States Status: Offline Points: 10753 |
Post Options
Thanks(0)
|
Brand, part number of flywheel ?
|
|
schultz227
Groupie Joined: August-20-2019 Location: Indiana Status: Offline Points: 49 |
Post Options
Thanks(0)
|
Shifts like butter no rattles
|
|
schultz227
Groupie Joined: August-20-2019 Location: Indiana Status: Offline Points: 49 |
Post Options
Thanks(0)
|
Also there under load obviously
|
|
schultz227
Groupie Joined: August-20-2019 Location: Indiana Status: Offline Points: 49 |
Post Options
Thanks(0)
|
Correct , no load
|
|
KENO
Grand Poobah Joined: June-06-2004 Location: United States Status: Offline Points: 10753 |
Post Options
Thanks(0)
|
We're just thinking alike, I'm not as speedy as you today though I was distracted looking at some Monty Python stuff |
|
Gary S
Grand Poobah Joined: November-30-2006 Location: Illinois Status: Offline Points: 14096 |
Post Options
Thanks(0)
|
slipping....
|
|
KENO
Grand Poobah Joined: June-06-2004 Location: United States Status: Offline Points: 10753 |
Post Options
Thanks(0)
|
Would you know the brand and part number of the flywheel?
So when you rev it up in neutral (no load) you get the vibration? |
|
Gary S
Grand Poobah Joined: November-30-2006 Location: Illinois Status: Offline Points: 14096 |
Post Options
Thanks(0)
|
Do you have the O'Reilly's part number for the flywheel?
|
|
schultz227
Groupie Joined: August-20-2019 Location: Indiana Status: Offline Points: 49 |
Post Options
Thanks(0)
|
Firing order wasn’t messed with , it ran smooth as silk before the work . Shifts in and out of gear like butter . When you rev the engine in comes the vibration
|
|
schultz227
Groupie Joined: August-20-2019 Location: Indiana Status: Offline Points: 49 |
Post Options
Thanks(0)
|
351 with the 123:1 tranny Mallory ignition . Parts came from oreilly and are supposed to be marine specific .
|
|
Gary S
Grand Poobah Joined: November-30-2006 Location: Illinois Status: Offline Points: 14096 |
Post Options
Thanks(0)
|
|
|
KENO
Grand Poobah Joined: June-06-2004 Location: United States Status: Offline Points: 10753 |
Post Options
Thanks(0)
|
It looks like you have a 92 SNOB with a 351W.
Does it have the ProTec ignition system or a regular distributor. And there's a reason for asking that |
|
KENO
Grand Poobah Joined: June-06-2004 Location: United States Status: Offline Points: 10753 |
Post Options
Thanks(0)
|
And while you're at it...........your favorite color, the name of your first pet and the street you lived on as a kid
|
|
8122pbrainard
Grand Poobah Joined: September-14-2006 Location: Three Lakes Wi. Status: Offline Points: 41040 |
Post Options
Thanks(0)
|
And the firing order you are using?
|
|
MrMcD
Grand Poobah Joined: January-28-2014 Location: Folsom, CA Status: Offline Points: 3610 |
Post Options
Thanks(0)
|
How about some details. What engine are you working on? Ford, Chevy?
Some flywheels are for an internally balanced engine, some are for external balance. You need to know more to get good answers. |
|
Gary S
Grand Poobah Joined: November-30-2006 Location: Illinois Status: Offline Points: 14096 |
Post Options
Thanks(0)
|
What engine, where did you get the flywheel? What was so wrong that it needed to be replaced?
|
|
schultz227
Groupie Joined: August-20-2019 Location: Indiana Status: Offline Points: 49 |
Post Options
Thanks(0)
|
Replaced the damper plate now it revs up very rough not under load , any thoughts on alignment? 1,000 in on this project and the boat runs rough Needed a new flywheel because of starter problem . Replaced the damper and the rear main seal too . Any help appreciated so frustrating
|
|
Post Reply | Page <12 |
Tweet
|
Forum Jump | Forum Permissions You cannot post new topics in this forum You cannot reply to topics in this forum You cannot delete your posts in this forum You cannot edit your posts in this forum You cannot create polls in this forum You cannot vote in polls in this forum |