351 running rough |
Post Reply | Page 12> |
Author | |||
Jason
Newbie Joined: August-06-2006 Location: Afghanistan Status: Offline Points: 12 |
Post Options
Thanks(0)
Posted: September-10-2011 at 1:56am |
||
There shouldn't be any fuel spraying into the body at idle. You said that when it started it was idling at 200. You had to crank up the idle screw to get it to 600. I'm no Dolley expert but this tells me that your idle circuit is blocked and you are having to use your primary circuit to get it to run. Fix your known issue, your carb, then move on to other potential issues like your spark. More than likely there rated by having rich mixture. I dealt with this issue and had my car rebuilt two times in a row then ended up buying new and never looked back. By the way red flags are flying with a kit not having a replacement float bowl needle valve.
|
|||
DrCC
Grand Poobah Joined: April-12-2004 Location: at home Status: Offline Points: 2867 |
Post Options
Thanks(0)
|
||
Man, That sounds good!!! BB-Q at BD boys house tomorrow!
Have not read the entire thread, but, have you checked for water in the tank? You don't have to drain the whole tank to remove the water off of the bottom. Whenever I suspect fuel issues, that's where I begin. |
|||
Luchog
Grand Poobah Joined: April-17-2007 Location: Argentina Status: Offline Points: 2135 |
Post Options
Thanks(0)
|
||
Brian, yes, the erratic timing problem went away with the new spring, later that same cap had moisture issues and put and old one back on with the "improved" spring and it's been working flawesly since.
|
|||
kapla
Grand Poobah Joined: March-27-2008 Location: BA, Argentina Status: Offline Points: 6148 |
Post Options
Thanks(0)
|
||
hey dog!! let´s have some lunch!!! tomorrow if you happen to be in BA don´t miss my BD barbecue!!! |
|||
<a href="">1992 ski nautique
|
|||
Bri892001
Grand Poobah Joined: September-27-2008 Location: Boston MA Status: Offline Points: 4947 |
Post Options
Thanks(0)
|
||
LOL, my eyes always read your name that way.
Did that the new spring and button fix your dist cap issue from before? |
|||
Luchog
Grand Poobah Joined: April-17-2007 Location: Argentina Status: Offline Points: 2135 |
Post Options
Thanks(0)
|
||
lunchdog????
|
|||
eric lavine
Grand Poobah Joined: August-13-2006 Location: United States Status: Offline Points: 13413 |
Post Options
Thanks(0)
|
||
if the gas is not spraying (atomizing) and its streamimg, this will cause a rich condition. the venturi effect should atomize the fuel, just like a paint spray can, when atomized the flashpoint is lowered, you should get a nice atomized spray down the throat
|
|||
"the things you own will start to own you"
|
|||
Bri892001
Grand Poobah Joined: September-27-2008 Location: Boston MA Status: Offline Points: 4947 |
Post Options
Thanks(0)
|
||
Make sure your rotor is all the way seated. If it's sitting to high, you might not be getting the cap all the way down.
I remember this old thread http://www.correctcraftfan.com/forum/forum_posts.asp?TID=19567&PID=250303&title=distributor-cap-carbon-pill-issue. Lunchdog was having trouble with the spring that holds the carbon pill from the cap down onto the top of the rotor. Just another thing to check. |
|||
Jllogan
Platinum Member Joined: May-18-2011 Location: canton, OH Status: Offline Points: 1728 |
Post Options
Thanks(0)
|
||
Ya, if signs point to the dizzy it could be the cap, even though its new I suppose anything can happen. I bought a genuine PCM cap from skidim but I feel like the gasket is cheap and I have a hard time getting it to lay right. Its like the gasket is almost too small or something. |
|||
89Martinique
Senior Member Joined: September-05-2011 Location: Binghamton Status: Offline Points: 457 |
Post Options
Thanks(0)
|
||
try a new distributor cap my dads friends' boat ran like crap and had a loud knock turned out to be a hair line crack in the new distributor cap causing cylinder #7 to fire with every other cylinder we put the old one on it ran great
|
|||
Current Boats:
1992 Supra Comp-TS6M PCM 351w HO Pro Boss Pro-Tec Ignition - Full Composite (no wood stingers!) 1989 (3rd Gen) Correct Craft Martinique B/R PCM 351w Power Plus 1984 E-Scow Keuka Lake, |
|||
Jllogan
Platinum Member Joined: May-18-2011 Location: canton, OH Status: Offline Points: 1728 |
Post Options
Thanks(0)
|
||
Ya, it was a holley renew kit. It was at the beginning of the summer so maybe I just forgot or lost it somehow. I am pretty sure I didnt replace and didnt get one. Well jury is still out on carb, seems to be better now. If I can get it tuned Ill leave it. If not I feel more comfortable with where stuff goes as I have had it apart before. This time I will soak it overnight and replace everything!!! Someone also told me to add a little water remover to that carb cleaner, not sure if thats necessary. |
|||
TRBenj
Grand Poobah Joined: June-29-2005 Location: NWCT Status: Offline Points: 21169 |
Post Options
Thanks(0)
|
||
Did you get a genuine Holley rebuild kit? Ive never seen rebuild kit that didnt include a needle/seat. I would think thats the #1 most important part to replace during a rebuild.
|
|||
Jllogan
Platinum Member Joined: May-18-2011 Location: canton, OH Status: Offline Points: 1728 |
Post Options
Thanks(0)
|
||
I replaced everything that my rebuild kit came with. I didnt realize until later that those needed to be purchased separate from the kit. I didnt replace the floats (I have the black plastic ones) or the idle mix screws because these not included in my kit either. Everything in the kit went it. I did just use the aerosol cleaner and compressed air . If I rebuild again, I will soak over night. I was worried I would lose track of where things went if I completely dissassembled so I tried to work on it one side at a time and then put it back together right away. Also when I rebuilt the carb it was due to a fuel leak and not because it wasnt running right, so I decided if it wasnt broke and it didnt come in the kit I wasnt going to worry about it. |
|||
8122pbrainard
Grand Poobah Joined: September-14-2006 Location: Three Lakes Wi. Status: Offline Points: 41045 |
Post Options
Thanks(0)
|
||
Justin, I have to ask why you didn't do a full rebuild on the carb. The needle and seat are key componemts. What else did you leave out? Did you soak the carb in a carb cleaner or just try to use one of the aerosol carb cleaners? Did you blow all the passages out with compressed air? |
|||
Jllogan
Platinum Member Joined: May-18-2011 Location: canton, OH Status: Offline Points: 1728 |
Post Options
Thanks(0)
|
||
Ok thats good advice. It is definitely running rich, I can tell from the exhaust smell and the plugs are black. Some worse that others. The four outside corner cylinders (the ones that show good spark)are clean. So the good news is, I can say with good certainty the issue is carb or dizzy. The bad news is both those parts are expensive. Bummer. I will have time to fiddle again tonight, I plan to try and rule out the dizzy and re-adjust the mix screws. I am going to first check weak spark plugs outside the engine by holding to the block with the inline light tester to see if it is stronger, this will rule out rich mix choking spark. If that is still showing weak, I will then check the points gap on every lobe to check for wear there and inspect closer for any dizzy cam play or wear. If at any point these check out, I will then turn my attention to adjusting the carb. Thanks for all your help and advice. I am better armed to tackle this issue with your shared experiences and comments! |
|||
gun-driver
Grand Poobah Joined: July-18-2008 Location: Pittsburgh, Pa Status: Offline Points: 4127 |
Post Options
Thanks(0)
|
||
Your plugs tips will be black/carbon if rich, white/gray if lean.
If only one or some of the plugs are fouled/black and others are burning properly then it’s probably a ignition problem. |
|||
Jllogan
Platinum Member Joined: May-18-2011 Location: canton, OH Status: Offline Points: 1728 |
Post Options
Thanks(0)
|
||
yes,
wires are new as of 20 hours ago and I double checked them by switching them with the strong sparking cylinder. What do you mean by my plugs should tell me if its a fuel/air problem? is that why I have weak spark in the middle four cylinders? |
|||
gun-driver
Grand Poobah Joined: July-18-2008 Location: Pittsburgh, Pa Status: Offline Points: 4127 |
Post Options
Thanks(0)
|
||
If it's a fuel/air problem your plugs should tell you if thats the problem.
Have you checked your wires? 79 where are you!!!! |
|||
lison
Newbie Joined: August-24-2011 Location: Forest Lake, MN Status: Offline Points: 21 |
Post Options
Thanks(0)
|
||
This all sounds so familiar. I went through the same thing for an entire season. Plugs, points, condenser, cap, rotor, wires, rebuilt carb,drained all old gas, fuel filter, fuel separator, finally decided it had to be carberation and took carb back into carb shop and had it gone through again. Still the same lag, wouldn't idle right, quit at low speeds. Talked to the guys at skidim about all the bad gas we have here in MN and decided to bite the bullet and buy a new carb. Bolted it on and the Nautique has never run better. I think the small orifices in low speed get corroded and if the rebuilder doesn't soak it long enough to get those cleaned out, it doesn't fix the issue. Good luck. It's pretty frustrating.
|
|||
L Ison
1984 CC Ski Nautique 2001 351 PCM Ford Forest Lake, MN Crandon, WI |
|||
SNobsessed
Grand Poobah Joined: October-21-2007 Location: IA Status: Offline Points: 7102 |
Post Options
Thanks(0)
|
||
Attach a plug wire & plug directly to the coil output (center terminal) & crank it over. You should get a good blue spark.
If your dizzy has any shaft play, or is rusty, time for a new one. I got a great deal from ebay, NIB prestolite electronic for $50. So there are deals out there if you are patient. |
|||
“Beer is proof that God loves us and wants us to be happy.”
Ben Franklin |
|||
Jllogan
Platinum Member Joined: May-18-2011 Location: canton, OH Status: Offline Points: 1728 |
Post Options
Thanks(0)
|
||
I tested as soon as I started the engine and it still read weak. I suppose though that if the mix was bad in those cylinders you would never get good spark because of too much gas. The carb appears to functioning properly or at least acceptably now. Its hard to really tell how it is running now until I drop it in the water. It may be ok for a while but if it keeps fouling plugs thats an issue.
Is there anyway to really isolate and test the spark from the dist? Right now I am torn between carb issue or dizzy issue and I need to eliminate one. (in the back of my mind there is still a possible valve issue, but since its both sides of the engine I am ruling that out right now.) Summit Racing has a new points dizzy for 189 or a new electronic for 269, do I need RH or LH rotation I always forget. I know skidim has them but they are more expensive. I would probably throw on a new mallory coil too (so it matches). I need a way to pinpoint the dizzy though before I drop 300 bucks. |
|||
Bri892001
Grand Poobah Joined: September-27-2008 Location: Boston MA Status: Offline Points: 4947 |
Post Options
Thanks(0)
|
||
My guess is that the plugs already being fouled caused the the light to show weak for those cylinders.
The light is meant to show spark in the circuit, the plug has to fire to temporarily complete that circuit. I bet if you retested those cylinders with the light now, after replacing the plugs, it would show stronger. Your carb situation may have fouled the plugs to begin with. |
|||
Jllogan
Platinum Member Joined: May-18-2011 Location: canton, OH Status: Offline Points: 1728 |
Post Options
Thanks(0)
|
||
I agree to that the fact that it is strange but it definitely has weak spark on half on the rotation. I have had that cap on and off several times, you would think it would be fit sometimes. Maybe I should see if I could wiggle it while its running. There is no chance the coil could be weak and just cant keep up with the spark or something. The other thing is the cap is new as of a few months ago so you wouldnt think that would be the issue.
Maybe the dizzy is worn or something, I had it out and had some people look at it and it seemed fine but maybe its not. |
|||
SNobsessed
Grand Poobah Joined: October-21-2007 Location: IA Status: Offline Points: 7102 |
Post Options
Thanks(0)
|
||
The coil fires all cyls - so logic rules it out as the problem. The cap could be bad somehow, not seated or off center - sounds like the rotor is not centered in cap well to me. It is strange that 1/2 of the rotor rotation has good spark & the other half is poor!
|
|||
“Beer is proof that God loves us and wants us to be happy.”
Ben Franklin |
|||
Jllogan
Platinum Member Joined: May-18-2011 Location: canton, OH Status: Offline Points: 1728 |
Post Options
Thanks(0)
|
||
Ok so the tail chasing continues. I think there were and are a few things wrong with the engine. Tonight I tested the plug/plug wires with one of those inline spark testers and the spark on pistons 2,3,6 and 7 was very weak. The light was barely on and it was very bright on 1,4,5 and 8. Also I noticed that those are the first four and last four in the firing order (any correlation? what could cause that?). The cap is new but maybe it was weak or defective so it didnt last very long. I have had my hand on it quite a bit and never got shocked though.
So I thought the plugs might be fouled and I replaced them and the rough running improved. Now it was idleing much faster (600 before plugs and 1100 after new plugs), so I lowered the throttle/idle adjustment and then had to reset the timing. I checked the advance and it was reading 30 degrees at 2000 rpm which seems to be inline with what I understand it should be. So I am thinking the weak spark fouled the plugs. What could be causing weak spark on the 4 cylinders and good on the others? Could this be a bad coil or could that little light just be innacurate? |
|||
GottaSki
Grand Poobah Joined: April-21-2005 Location: NE CT Status: Offline Points: 3357 |
Post Options
Thanks(0)
|
||
Bet anything your idle circuit is clogged.
You shouldn't see anything from the main boosters at idle. |
|||
"There is nothing, absolutely nothing, half so much worthwhile as messing around with boats...simply messing."
River Rat to Mole |
|||
Jllogan
Platinum Member Joined: May-18-2011 Location: canton, OH Status: Offline Points: 1728 |
Post Options
Thanks(0)
|
||
I am thinking that by me adjusting the throttle linkage/idle is why its squirting in gas. By screwing it down its the equivalent of throttling up. There is no dripping after I shut it off thats what makes me think the floats are ok.
Who knows Ill test a few more things tonight and see what I come up with. |
|||
kapla
Grand Poobah Joined: March-27-2008 Location: BA, Argentina Status: Offline Points: 6148 |
Post Options
Thanks(0)
|
||
yes, and the idle circuit as well (think). But if you are dripping most likely your floats are not closing right...you should see no dripping @ idle...only a nice even squirt when you hit the throtle....
|
|||
<a href="">1992 ski nautique
|
|||
Jllogan
Platinum Member Joined: May-18-2011 Location: canton, OH Status: Offline Points: 1728 |
Post Options
Thanks(0)
|
||
well it stumbles to start with. Ill screw them in all the way and see if there is a change.
|
|||
Bri892001
Grand Poobah Joined: September-27-2008 Location: Boston MA Status: Offline Points: 4947 |
Post Options
Thanks(0)
|
||
LOL.
Kap, I think the test you mention above is a test of the powervalve. If the engine keeps running the same with them closed all the way, it means the powervalve is ruptured. |
|||
Post Reply | Page 12> |
Tweet
|
Forum Jump | Forum Permissions You cannot post new topics in this forum You cannot reply to topics in this forum You cannot delete your posts in this forum You cannot edit your posts in this forum You cannot create polls in this forum You cannot vote in polls in this forum |