Boats For Sale:
PCM 40 Transmission Question |
Post Reply 
|
| Author | |
eric lavine 
Grand Poobah 
Joined: August-13-2006 Location: United States Status: Offline Points: 13413 |
 Post Options
 Thanks(0)
 Quote Reply
 Topic: PCM 40 Transmission QuestionPosted: August-10-2008 at 4:16pm |
|
on the PCM? they are sometimes very tight and heat is a must, and a 1/2 impact, you do get a new one in the seal and gasket kit so dont worry about destroying the nut 36mm? i believe thin wall
|
|
|
"the things you own will start to own you"
|
|
 |
|
|
dcoll
Senior Member 
Joined: August-06-2006 Location: Manchester, MD Status: Offline Points: 122 |
Post Options
Thanks(0)
Quote Reply
Posted: August-10-2008 at 3:59pm |
|
Eric, I am trying to remove the output shaft nut. Wow, that is tight. My compressr is down so I went next door and his compressor with his impact wrench did not move the nut. I do not want to heat the nut. I think i need to take to a shop with more air and a better impact wrench. How do you remove that nut?
|
|
|
1997 Super Sport Nautique
|
|
|
|
|
eric lavine
Grand Poobah
Joined: August-13-2006 Location: United States Status: Offline Points: 13413 |
Post Options
Thanks(0)
Quote Reply
Posted: August-08-2008 at 11:21am |
|
look closely at the forward drum near the seal ring area, look for a hairline crack,and scoring in the case bore where the seal rings ride. JA Chamberlin may have better pricing on the seal kit
|
|
|
"the things you own will start to own you"
|
|
|
|
|
dcoll
Senior Member
Joined: August-06-2006 Location: Manchester, MD Status: Offline Points: 122 |
Post Options
Thanks(0)
Quote Reply
Posted: August-08-2008 at 10:12am |
|
Yes between the V-Drive and the Walters. Dexron it is. I am the same guy with pink trans fluid. Need a new oil cooler. I have inspected the clutches both reverse and forward and they look fine. All gears are fine. I will be removing the output shaft nut today so that I can remove the drum for further inspection. I will be ordering a seal kit from skidim. There is no burning smell or any scorched metal. I think I got lucky.
|
|
|
1997 Super Sport Nautique
|
|
|
|
|
eric lavine
Grand Poobah
Joined: August-13-2006 Location: United States Status: Offline Points: 13413 |
Post Options
Thanks(0)
Quote Reply
Posted: August-08-2008 at 9:47am |
|
between the v-drive and the front half? if so, no
there is also a front seal on the walter's, is it Dexron or 30w? |
|
|
"the things you own will start to own you"
|
|
|
|
|
dcoll
Senior Member
Joined: August-06-2006 Location: Manchester, MD Status: Offline Points: 122 |
Post Options
Thanks(0)
Quote Reply
Posted: August-07-2008 at 11:36pm |
|
While removing the trans I have notice that there is trans fluid in the aft section. Is there suppose to be fluid in there or is the seal leaking? I am referring to area beneath the linkage mounting plate.
|
|
|
1997 Super Sport Nautique
|
|
|
|
|
Post Reply
|
|
Tweet
|
| Forum Jump | Forum Permissions You cannot post new topics in this forum You cannot reply to topics in this forum You cannot delete your posts in this forum You cannot edit your posts in this forum You cannot create polls in this forum You cannot vote in polls in this forum |
Topic Options