Boats For Sale:
carb issues.. oh what fun.. |
Post Reply 
|
| Author | |
boat dr 
Grand Poobah 
Joined: June-27-2004 Location: United States Status: Offline Points: 4245 |
 Post Options
 Thanks(0)
 Quote Reply
 Topic: carb issues.. oh what fun..Posted: June-05-2010 at 3:03pm |
|
That is correct for points type ignition.
Electronic ignition with a good coil will allow a wider gap....... |
|
 |
|
|
boat dr
Grand Poobah
Joined: June-27-2004 Location: United States Status: Offline Points: 4245 |
Post Options
Thanks(0)
Quote Reply
Posted: June-05-2010 at 2:56pm |
|
Have you pulled a plug or two for a visual check ?These readings can tell you a lot about your motor and its condition internally....
Slow cam timing,i.e.timing chain wear, will give some of the same symptoms you describe. |
|
|
|
|
trn448s
Newbie 
Joined: May-23-2010 Location: Lake Lotawana Status: Offline Points: 27 |
Post Options
Thanks(0)
Quote Reply
Posted: June-05-2010 at 2:55pm |
|
.035 i believe is the proper gap
|
|
|
|
|
trn448s
Newbie
Joined: May-23-2010 Location: Lake Lotawana Status: Offline Points: 27 |
Post Options
Thanks(0)
Quote Reply
Posted: June-05-2010 at 2:20pm |
|
what is the proper gap on spark plugs as well.. maybe i have this wrong..
thanks everyone!! |
|
|
|
|
trn448s
Newbie
Joined: May-23-2010 Location: Lake Lotawana Status: Offline Points: 27 |
Post Options
Thanks(0)
Quote Reply
Posted: June-05-2010 at 1:46pm |
|
power valve is a 6.5 and the plugs where replaced this year
|
|
|
|
|
boat dr
Grand Poobah
Joined: June-27-2004 Location: United States Status: Offline Points: 4245 |
Post Options
Thanks(0)
Quote Reply
Posted: June-04-2010 at 2:51pm |
|
Accelerator pump stroke nor cam need adjustment if Holley parts are used.This is a DFW screw..........
What power valve did you install? New PCM 4160 Holley carbs come with a 2.5 All kits bought from PCM come with the same Probably not the PV that you installed,6.5 or 7.5 possibly Do a plug check, easy way to observe fuel mixture. Black is not GOOD Chocolate Brown = correct Blistered or very clean= too lean |
|
|
|
|
79nautique
Grand Poobah
Joined: January-27-2004 Location: United States Status: Offline Points: 7872 |
Post Options
Thanks(0)
Quote Reply
Posted: June-04-2010 at 10:28am |
What is your base timing set at? and what is the timing at 2K rpm's? |
|
|
|
|
horkn
Platinum Member 
Joined: September-10-2007 Location: Cedarburg, Wi Status: Offline Points: 1511 |
Post Options
Thanks(0)
Quote Reply
Posted: June-04-2010 at 1:45am |
|
Have you adjusted the accelerator pump? Does it start a nice spray even between both barrels as soon as the throttle is touched?
|
|
|
78 martinique- refloored, reinforced, stringers re glassed, re engineered interior
GT40P heads Edelbrock Performer intake acme 4 blade http://img.photobucket.com/albums/v64/horkn/fish/nautique.jpg |
|
|
|
|
trn448s
Newbie
Joined: May-23-2010 Location: Lake Lotawana Status: Offline Points: 27 |
Post Options
Thanks(0)
Quote Reply
Posted: June-04-2010 at 12:40am |
|
so basically after my wonderful fuel filter breakdown i decided to pull the carb apart clean and rebuild. I have never really had a strong boat like others. It had a hick up right out of the hole. so it never was strong. I have rode behind other boats and they can pull arms off people when pulling skiers. pulling the carb apart i replaced the power valve and made sure both floats where parallel to the housing when held upside down. injectors cleaned, but i am still having isssues. I don't have the hick up anymore but it is slugish out of the hole. from 20mphs and up it is strong, but it is slugish from 0-10 or so. Its not bad just i know the boat can do more and i can't figure it out for the life of me..
any help would be great.. Tommy |
|
|
|
|
Post Reply
|
|
Tweet
|
| Forum Jump | Forum Permissions You cannot post new topics in this forum You cannot reply to topics in this forum You cannot delete your posts in this forum You cannot edit your posts in this forum You cannot create polls in this forum You cannot vote in polls in this forum |
Topic Options
trn448s wrote: