Boats For Sale:
2002 super air heater lines |
Post Reply 
|
| Author | |
mike32 
Groupie 
Joined: November-27-2011 Location: lanc, ohio Status: Offline Points: 66 |
 Post Options
 Thanks(0)
 Quote Reply
 Topic: 2002 super air heater linesPosted: May-13-2012 at 7:12pm |
|
I bought it sight unseen and was told it had a gt40. Just like I was told alot of other things that weren't true. But it is a brand new motor and it does run great.
|
|
 |
|
|
8122pbrainard
Grand Poobah 
Joined: September-14-2006 Location: Three Lakes Wi. Status: Offline Points: 41045 |
Post Options
Thanks(0)
Quote Reply
Posted: May-13-2012 at 6:18pm |
I take it you don't like GM engines! If that is the case, why did you buy it?  Do you plans call for another engine that isn't a GM? 
|
|
|
|
|
mike32
Groupie
Joined: November-27-2011 Location: lanc, ohio Status: Offline Points: 66 |
Post Options
Thanks(0)
Quote Reply
Posted: May-13-2012 at 6:14pm |
|
Well I didn't have the motor installed the consignment dealer did. So this was done right before I bought it and the heater core was disconnected due to being busted. They probably didn't worry about the fitting because of this. As to why the motor was replaced, I don't know why, they didn't tell me but I would assume because it is a gm motor:)
|
|
|
|
|
8122pbrainard
Grand Poobah
Joined: September-14-2006 Location: Three Lakes Wi. Status: Offline Points: 41045 |
Post Options
Thanks(0)
Quote Reply
Posted: May-13-2012 at 7:23am |
|
I'd sure go back to whoever put the engine in and ask them why the job was not completed! Why the new engine?
|
|
|
|
|
mike32
Groupie
Joined: November-27-2011 Location: lanc, ohio Status: Offline Points: 66 |
Post Options
Thanks(0)
Quote Reply
Posted: May-13-2012 at 1:24am |
|
It looks like I just have a temp sensor located in that connection where that hose connects on the manifold and also another sensor at 90 degrees from that on the front of the manifold. Do I need to install a tee fitting there to still use the sensor location? I would assume that one sensor is for guage and the other is for the efi system, one has a green wire and the other has a white wire. Is there another port that I am missing? They just put a new engine in this boat before I bought it and I wonder if they just didn't put the correct fitting back in. The one on top has a fuel rail over it and I think it might be difficult to add a tee.
|
|
|
|
|
quinner
Grand Poobah
Joined: October-12-2005 Location: Unknown Status: Offline Points: 5828 |
Post Options
Thanks(0)
Quote Reply
Posted: May-12-2012 at 1:37pm |
|
Yes on the red hose at the intake manifold.
Ordered with a heater so I would assume it was a factory install. |
|
|
|
|
mike32
Groupie
Joined: November-27-2011 Location: lanc, ohio Status: Offline Points: 66 |
Post Options
Thanks(0)
Quote Reply
Posted: May-12-2012 at 1:13pm |
|
I have an apex. In the first pic I have the line coming from the motor water pump connected. Then in the second picture, is that it coming from the top of the intake manifold(red hose)?
|
|
|
|
|
quinner
Grand Poobah
Joined: October-12-2005 Location: Unknown Status: Offline Points: 5828 |
Post Options
Thanks(0)
Quote Reply
Posted: May-12-2012 at 11:32am |
|
Suppose you either have a GT-40 or an Excalibur, pics are an Excal. Not sure if a GT-40 is plumbed the same.
 
|
|
|
|
|
mike32
Groupie
Joined: November-27-2011 Location: lanc, ohio Status: Offline Points: 66 |
Post Options
Thanks(0)
Quote Reply
Posted: May-12-2012 at 1:22am |
|
Does anyone have a diagram that shows where the heater lines go to? I have one connected to a valve and the other laying in the bottom of boat. thanks
|
|
|
|
|
Post Reply
|
|
Tweet
|
| Forum Jump | Forum Permissions You cannot post new topics in this forum You cannot reply to topics in this forum You cannot delete your posts in this forum You cannot edit your posts in this forum You cannot create polls in this forum You cannot vote in polls in this forum |
Topic Options
mike32 wrote: