Tee Nuts |
Post Reply |
Author | |
nautique frk
Platinum Member Joined: February-16-2004 Location: United States Status: Offline Points: 1784 |
Post Options
Thanks(0)
Posted: May-16-2012 at 4:52pm |
Yo Yo Yo What up "Tee Nutz" !! Newest Rapper :)
|
|
Bri892001
Grand Poobah Joined: September-27-2008 Location: Boston MA Status: Offline Points: 4947 |
Post Options
Thanks(0)
|
"Tee Nuts" would be a good stage name for a rap star
|
|
8122pbrainard
Grand Poobah Joined: September-14-2006 Location: Three Lakes Wi. Status: Offline Points: 41045 |
Post Options
Thanks(0)
|
Epoxy in place:
|
|
SNobsessed
Grand Poobah Joined: October-21-2007 Location: IA Status: Offline Points: 7102 |
Post Options
Thanks(0)
|
Jim - Sorry for my left-field answer. I can see how the tangs of a tee nut wouldn't dig into fiberglass. Poor design from the factory in the 1st place.
|
|
“Beer is proof that God loves us and wants us to be happy.”
Ben Franklin |
|
winniskier
Senior Member Joined: March-15-2008 Location: Gilford, NH Status: Offline Points: 193 |
Post Options
Thanks(0)
|
Yes, it is fiberglass. I turns out that it is not the problem that I expected. The tee nut does not anchor on the hard backside/inside of the upholstered panel. The hinge connects to the fiberglass seat structure, then the upholstered panel attaches by a separate fastener to the seat structure. I can attach the hinge using nuts and bolts. I’ve run into this issue a number of times with other boats. The above advice will come in handy next time. Yes JoeinNY did take the world’s slowest SN2001 off my hands so I could buy the boat that I should have bought the first time. All good now. |
|
Jim
|
|
lewy2001
Grand Poobah Joined: March-19-2008 Location: NSW Australia Status: Offline Points: 2234 |
Post Options
Thanks(0)
|
Yeh Alan sounds like he has a 97 no wood.
Jim not quite sure what the problem you are describing is do you have a picture of it? But the interesting info in the diary entry was that he actually sold JoeinNY the future worlds fastest SN2001. |
|
If you're going through hell, keep going
89 Ski <a href="http://www.correctcraftfan.com/diaries/details.asp?ID=5685" ta |
|
81nautique
Grand Poobah Joined: September-03-2005 Location: Big Rock, Il Status: Offline Points: 5779 |
Post Options
Thanks(0)
|
If we're talking about the 97 in his avatar he doesn't have wood for seat backs. He doesn't mention wood in his post just wood screws. I would remove the staples and either insert new tee nuts if possible or attach a 1/8 thick backer strip of aluminum or stainless and through drill and fasten with nut and bolt if there is room.
And then go tell your upholstery guy he's a morron. |
|
You can’t change the wind but you can adjust your sails
|
|
SNobsessed
Grand Poobah Joined: October-21-2007 Location: IA Status: Offline Points: 7102 |
Post Options
Thanks(0)
|
Take a large hole saw & cut a plug around where the Tee nut went. Make a mating plug to refit, putting the tee nut in that. You might want to epoxy in a couple of thin wood 'slats', off-center of the hole (a door frame shim would work) to give a back stop. Then epoxy the plug back in. It would have been much easier to replace the wood when the skin was off!
|
|
“Beer is proof that God loves us and wants us to be happy.”
Ben Franklin |
|
8122pbrainard
Grand Poobah Joined: September-14-2006 Location: Three Lakes Wi. Status: Offline Points: 41045 |
Post Options
Thanks(0)
|
Jim,
The T nuts are in there since wood screws or even fully threaded type "A" sheet metal screws won't handle the load. I suggest removing enough staples to get the T nuts back in the ply. If they are loose, epoxy them in. It sounds like maybe the upholsterer should have put in new wood? |
|
winniskier
Senior Member Joined: March-15-2008 Location: Gilford, NH Status: Offline Points: 193 |
Post Options
Thanks(0)
|
I had the upholstery re-skinned over the winter. I removed the pieces from the boat myself and delivered them to the upholsterer. The piano hinge at the top of the observer’s seat was anchored by a screw into a tee nut attached to the backside/ inside of the seat frame. The tee nuts had loosened up over time. Rather than fix or replace them, the upholsterer removed them and suggested wood screws. To me, this is not optimal since they have greater chance of loosening up in this type of use. I now can’t get access to the inside/backside of the seat frame, so tee nuts are not an option. Any suggestion as to what I could use that would be the equivalent of the tee nuts?
|
|
Jim
|
|
Post Reply | |
Tweet
|
Forum Jump | Forum Permissions You cannot post new topics in this forum You cannot reply to topics in this forum You cannot delete your posts in this forum You cannot edit your posts in this forum You cannot create polls in this forum You cannot vote in polls in this forum |