Boats For Sale:
Tranny seal |
Post Reply 
|
| Author | |
connorssons 
Platinum Member 
Joined: January-17-2009 Location: Michigan Status: Offline Points: 1414 |
 Post Options
 Thanks(0)
 Quote Reply
 Topic: Tranny sealPosted: June-24-2018 at 9:15am |
|
it was not leaking, just wanted to stick one in before motor was replaced. hello again Duane, and thank youPete
|
|
 |
|
|
8122pbrainard
Grand Poobah 
Joined: September-14-2006 Location: Three Lakes Wi. Status: Offline Points: 41045 |
Post Options
Thanks(0)
Quote Reply
Posted: June-23-2018 at 10:50am |
|
Jeff,
Duane is correct that if you need to get into the trans say for rebuilding, the sleeve does need to be cut off but, I don't feel that would be a major obstacle over a rebuild. The removal is due to the shoulder on the sleeve. 
|
|
|
|
|
Duane in Indy
Platinum Member
Joined: October-26-2015 Location: Indiana Status: Offline Points: 1578 |
Post Options
Thanks(0)
Quote Reply
Posted: June-23-2018 at 10:34am |
|
Speedy Sleeves are a great fix for worn shafts, but bear in mind that you will have to cut it off the shaft to remove anymore than the front cover. Just make sure that you don't have to dig any farther than the front cover before you install it.
|
|
|
Keep it as original as YOU want it
1978 Mustang (modified) |
|
|
|
|
8122pbrainard
Grand Poobah
Joined: September-14-2006 Location: Three Lakes Wi. Status: Offline Points: 41045 |
Post Options
Thanks(0)
Quote Reply
Posted: June-23-2018 at 8:17am |
|
Jeff,
An auto parts store Was there a leak when it was running before? |
|
|
|
|
connorssons
Platinum Member
Joined: January-17-2009 Location: Michigan Status: Offline Points: 1414 |
Post Options
Thanks(0)
Quote Reply
Posted: June-23-2018 at 8:05am |
|
if its needed pete, where do you get one of those?
|
|
|
|
|
8122pbrainard
Grand Poobah
Joined: September-14-2006 Location: Three Lakes Wi. Status: Offline Points: 41045 |
Post Options
Thanks(0)
Quote Reply
Posted: June-22-2018 at 4:16pm |
|
Jeff,
Take a close look at the shaft. If it looks bad, you may want to put a speedy sleeve on it. |
|
|
|
|
connorssons
Platinum Member
Joined: January-17-2009 Location: Michigan Status: Offline Points: 1414 |
Post Options
Thanks(0)
Quote Reply
Posted: June-22-2018 at 3:38pm |
|
Thank you so much for the information especially on the other name brands getting ready to put the big block in my Barefoot and wanted to replace the seal!
|
|
|
|
|
KENO
Grand Poobah
Joined: June-06-2004 Location: United States Status: Offline Points: 11093 |
Post Options
Thanks(0)
Quote Reply
Posted: June-21-2018 at 10:35pm |
It's the same as a 71C seal PCM part number is R047003 National 470774 Alto 023420 and a bunch of others will cross reference 1.375 ID 2.0662 OD .375 width |
|
|
|
|
connorssons
Platinum Member
Joined: January-17-2009 Location: Michigan Status: Offline Points: 1414 |
Post Options
Thanks(0)
Quote Reply
Posted: June-21-2018 at 6:52pm |
|
Does anybody off hand know the input shaft seal replacement number on a 72c Velvet Drive
|
|
|
|
|
Post Reply
|
|
Tweet
|
| Forum Jump | Forum Permissions You cannot post new topics in this forum You cannot reply to topics in this forum You cannot delete your posts in this forum You cannot edit your posts in this forum You cannot create polls in this forum You cannot vote in polls in this forum |
Topic Options
connorssons wrote: