Boats For Sale:
Water coming out of drive shaft 2003 SAN 210 TE |
Post Reply 
|
| Author | |
SNobsessed 
Grand Poobah 
Joined: October-21-2007 Location: IA Status: Offline Points: 7102 |
 Post Options
 Thanks(0)
 Quote Reply
 Topic: Water coming out of drive shaft 2003 SAN 210 TEPosted: June-26-2020 at 9:31am |
|
Do you have a dripless shaft seal with a water line going to it?
How about a picture? |
|
|
“Beer is proof that God loves us and wants us to be happy.”
Ben Franklin |
|
 |
|
|
8122pbrainard
Grand Poobah
Joined: September-14-2006 Location: Three Lakes Wi. Status: Offline Points: 41045 |
Post Options
Thanks(0)
Quote Reply
Posted: June-26-2020 at 8:27am |
|
Austin,
Yes, I agree with Ken that you have a dripless seal. I have a question/suggestion. Have you been running the boat out of the water without any water connection? If so I highly recommend not doing it. The RWP (raw water pump) rubber impeller is water lubricated so without water it doesn't take very much time to burn up the impeller. Even the scenario " I had better start the engine before we get down the ramp just to make sure it will start" will do it. BTW, I sure would at all costs avoid that dealer you called. If they couldn't figure out you have a dripless shaft seal, I wouldn't let them even look, touch and even worse work on my boat. |
|
|
|
|
KENO
Grand Poobah
Joined: June-06-2004 Location: United States Status: Offline Points: 11112 |
Post Options
Thanks(0)
Quote Reply
Posted: June-26-2020 at 7:25am |
If you're saying that water is leaking externally from the boat out onto the ground along the shaft, it sounds to me like you have a dripless shaft seal in the boat that uses water for lubrication and cooling of the seal and that what you're seeing is normal. There would be a small diameter piece of tubing tapping into the side of the seal inside the boat on most mechanical seals. If you have old style shaft packing, then something weird is going on here  A picture of the seal inside the boat would be worth a thousand words. |
|
|
|
|
Jonny Quest
Grand Poobah
Joined: August-20-2013 Location: Utah--via Texas Status: Offline Points: 2979 |
Post Options
Thanks(0)
Quote Reply
Posted: June-26-2020 at 3:00am |
|
Assuming that you have a standard packing type shaft seal, the shaft seal is designed to drip one drop of water every 10 seconds or so to keep the shaft cool when it’s spinning. If there’s too much water coming through the shaft, you can tighten the gland nut to reduce the flow of water as described above. The procedure is also described in you owners manual.
JQ |
|
|
Current
2003 Ski Nautique 206 Limited Previous 2001 Ski Nautique Open Bow 1994 Ski Nautique Open Bow Aqua skiing, ergo sum |
|
|
|
|
atalbert
Newbie 
Joined: June-24-2020 Location: Colorado Status: Offline Points: 2 |
Post Options
Thanks(0)
Quote Reply
Posted: June-26-2020 at 12:37am |
|
Last weekend my impeller went out on my 2003 SAN 210TE with a 330 Excalibur. While trouble shooting at the lake I took apart my water filter and poured water into the system toward the impeller and engine. When I do this water comes out where my shaft comes out of the hull towards my propeller. Is this normal? I called a dealer about 2.5 hrs away from me and they were no help what so ever. (They just want me to bring it in) When i got it home I took apart the impeller and it was shot and I have replaced that. Any advice would be appreciated. Hoping to get it on the water this weekend.
|
|
|
Austin
|
|
|
|
|
Post Reply
|
|
Tweet
|
| Forum Jump | Forum Permissions You cannot post new topics in this forum You cannot reply to topics in this forum You cannot delete your posts in this forum You cannot edit your posts in this forum You cannot create polls in this forum You cannot vote in polls in this forum |
Topic Options
atalbert wrote: