Boats For Sale:
1982 PCM pcv hose |
Post Reply 
|
| Author | |
MourningWood 
Gold Member 
Joined: June-13-2014 Location: NorCal Status: Offline Points: 917 |
 Post Options
 Thanks(0)
 Quote Reply
 Topic: 1982 PCM pcv hosePosted: January-07-2022 at 8:29pm |
|
Great. Thank you all.
|
|
|
1964 Dunphy X-55 "One 'N Dun"
'I measured twice, cut three times, and it's still too short!" |
|
 |
|
|
Gary S
Grand Poobah 
Joined: November-30-2006 Location: Illinois Status: Offline Points: 14096 |
Post Options
Thanks(0)
Quote Reply
Posted: January-05-2022 at 8:11pm |
|
Chances are it's not a PCM part anyway but in fact supplied by Ford. I had the same problem when looking for a replacement hose for my HM. Did my homework and found one here that worked- http://www.cjponyparts.com/catalogsearch/result/?q=289+pcv+hose
|
|
|
|
|
KENO
Grand Poobah
Joined: June-06-2004 Location: United States Status: Offline Points: 11112 |
Post Options
Thanks(0)
Quote Reply
Posted: January-05-2022 at 7:19pm |
|
I think if you measure the fitting on the PCV valve you'll figure out that a 3/8 ID hose is a good fit and if you measure the fitting on the spacer, it's slightly tapered and about 9/16 of an inch.
That's a lot of streeeetching for that poor 3/8 hose.  PCM had a part number for that hose. It's R045050. It comes with different ID ends. I have no idea if it's still available these days. I've used a 9/16 ID gas/oil hose that can clamp over the 9/16 fitting on the spacer and then with multiple sizes of heat shrink tubing, built up the fitting on the PCV so the hose slid over it and could be clamped on. No stretching needed
|
|
|
|
|
MourningWood
Gold Member
Joined: June-13-2014 Location: NorCal Status: Offline Points: 917 |
Post Options
Thanks(0)
Quote Reply
Posted: January-05-2022 at 6:17pm |
|
Thanks JQ
|
|
|
1964 Dunphy X-55 "One 'N Dun"
'I measured twice, cut three times, and it's still too short!" |
|
|
|
|
Jonny Quest
Grand Poobah
Joined: August-20-2013 Location: Utah--via Texas Status: Offline Points: 2979 |
Post Options
Thanks(0)
Quote Reply
Posted: January-05-2022 at 5:45pm |
|
Stretch. You don’t want air leaks. Nothing super special about PCV hose.
JQ
|
|
|
Current
2003 Ski Nautique 206 Limited Previous 2001 Ski Nautique Open Bow 1994 Ski Nautique Open Bow Aqua skiing, ergo sum |
|
|
|
|
MourningWood
Gold Member
Joined: June-13-2014 Location: NorCal Status: Offline Points: 917 |
Post Options
Thanks(0)
Quote Reply
Posted: January-05-2022 at 4:05pm |
|
The fitting on the carb spacer and the PCV valve don't match-the PCV valve being smaller. Is there a special hose for this, or just heat/stretch/force? Thanks
|
|
|
1964 Dunphy X-55 "One 'N Dun"
'I measured twice, cut three times, and it's still too short!" |
|
|
|
|
Post Reply
|
|
Tweet
|
| Forum Jump | Forum Permissions You cannot post new topics in this forum You cannot reply to topics in this forum You cannot delete your posts in this forum You cannot edit your posts in this forum You cannot create polls in this forum You cannot vote in polls in this forum |
Topic Options