Forums
NautiqueParts.comCalendar Photo Submission
  New Posts New Posts RSS Feed - damper plate test
  FAQ FAQ  Forum Search   Register Register  Login Login

damper plate test

 Post Reply Post Reply   
Author
ripsaw View Drop Down
Groupie
Groupie


Joined: April-04-2008
Location: United States
Status: Offline
Points: 86
Post Options Post Options   Thanks (0) Thanks(0)   Quote ripsaw Quote  Post ReplyReply Direct Link To This Post Topic: damper plate test
    Posted: April-08-2008 at 10:42pm
pulled the damper plate as eric said. Cleaned up on the work bench and it didn't look bad. Springs look fine with no cracks. If I need to get another one so be it, but is there any way to test them before I spend another $100.TIA Randy
Back to Top
Tim D View Drop Down
Grand Poobah
Grand Poobah


Joined: August-23-2004
Location: United States
Status: Offline
Points: 2641
Post Options Post Options   Thanks (0) Thanks(0)   Quote Tim D Quote  Post ReplyReply Direct Link To This Post Posted: April-08-2008 at 11:40pm
It's like the rear oil seal, while you have it broken down, might as well change it.
Tim D
Back to Top
eric lavine View Drop Down
Grand Poobah
Grand Poobah


Joined: August-13-2006
Location: United States
Status: Offline
Points: 13413
Post Options Post Options   Thanks (0) Thanks(0)   Quote eric lavine Quote  Post ReplyReply Direct Link To This Post Posted: April-08-2008 at 11:47pm
did you remove a spring and test the tension?
lol, you really cant tell spring tension, look where the spring ends meet the plate, look closely then report the findings. those springs sit in a perfect square hole and the wear in the corners are often missed.
i automatically replace them if a boat only has 400 hours on them when i have the trans out
"the things you own will start to own you"
Back to Top
ripsaw View Drop Down
Groupie
Groupie


Joined: April-04-2008
Location: United States
Status: Offline
Points: 86
Post Options Post Options   Thanks (0) Thanks(0)   Quote ripsaw Quote  Post ReplyReply Direct Link To This Post Posted: April-09-2008 at 12:06am
eric I looked at it again. I'm assuming you mean the housing holding the spring. I would say that is still square with maybe an 1/8" radius in each corner. Maybe I'm not following you.
Back to Top
8122pbrainard View Drop Down
Grand Poobah
Grand Poobah
Avatar

Joined: September-14-2006
Location: Three Lakes Wi.
Status: Offline
Points: 41045
Post Options Post Options   Thanks (0) Thanks(0)   Quote 8122pbrainard Quote  Post ReplyReply Direct Link To This Post Posted: April-09-2008 at 7:53am
Randy, The only way to check a spring to see if it may break is to X ray and look for the start of stress cracking. Just change that plate!!


54 Atom


77 Tique

64 X55 Dunphy

Keep it original, Pete
<
Back to Top
eric lavine View Drop Down
Grand Poobah
Grand Poobah


Joined: August-13-2006
Location: United States
Status: Offline
Points: 13413
Post Options Post Options   Thanks (0) Thanks(0)   Quote eric lavine Quote  Post ReplyReply Direct Link To This Post Posted: April-09-2008 at 10:03am
the 1/8 inch radius is wear
"the things you own will start to own you"
Back to Top
ripsaw View Drop Down
Groupie
Groupie


Joined: April-04-2008
Location: United States
Status: Offline
Points: 86
Post Options Post Options   Thanks (0) Thanks(0)   Quote ripsaw Quote  Post ReplyReply Direct Link To This Post Posted: April-09-2008 at 8:10pm
10/4 will do. I thought gas would break me this summer, but the winter parts and repairs might do it first. Do you want to send one back with the tranny or should I be looking elsewhere. It was shipped fed ex today. Just an added note, 60 degrees saturday and the ground was white last night. Winter has to end eventually doesn't it? Thanks eric.
Back to Top
BuffaloBFN View Drop Down
Grand Poobah
Grand Poobah
Avatar

Joined: June-24-2007
Location: Gainesville,GA
Status: Offline
Points: 6094
Post Options Post Options   Thanks (0) Thanks(0)   Quote BuffaloBFN Quote  Post ReplyReply Direct Link To This Post Posted: April-09-2008 at 8:15pm
Randy, he'll make you a good deal on a good plate...just call him the day he sends your tranny back to remind him to throw it in the box!
1988 BFN-sold



"It's a Livin' Thing...What a Terrible Thing to Lose" ELO
Back to Top
ripsaw View Drop Down
Groupie
Groupie


Joined: April-04-2008
Location: United States
Status: Offline
Points: 86
Post Options Post Options   Thanks (0) Thanks(0)   Quote ripsaw Quote  Post ReplyReply Direct Link To This Post Posted: April-09-2008 at 8:24pm
works for me thanks buffalo
Back to Top
BuffaloBFN View Drop Down
Grand Poobah
Grand Poobah
Avatar

Joined: June-24-2007
Location: Gainesville,GA
Status: Offline
Points: 6094
Post Options Post Options   Thanks (0) Thanks(0)   Quote BuffaloBFN Quote  Post ReplyReply Direct Link To This Post Posted: April-09-2008 at 9:56pm
Originally posted by ripsaw ripsaw wrote:

works for me thanks buffalo


Most welcome, he did a nice job for me. Mine was noisy and had the false neutral I've seen others here with recently. Now it's smoooth!

Of course, now that I've given him a compliment; you'll probably get 1 back that does 45mph in reverse?!!?
1988 BFN-sold



"It's a Livin' Thing...What a Terrible Thing to Lose" ELO
Back to Top
eric lavine View Drop Down
Grand Poobah
Grand Poobah


Joined: August-13-2006
Location: United States
Status: Offline
Points: 13413
Post Options Post Options   Thanks (0) Thanks(0)   Quote eric lavine Quote  Post ReplyReply Direct Link To This Post Posted: April-09-2008 at 10:47pm
it pushed MM's boat over 50 (he thought it was his engine) lol i still think he used a wind turbine to check his speed
"the things you own will start to own you"
Back to Top
eric lavine View Drop Down
Grand Poobah
Grand Poobah


Joined: August-13-2006
Location: United States
Status: Offline
Points: 13413
Post Options Post Options   Thanks (0) Thanks(0)   Quote eric lavine Quote  Post ReplyReply Direct Link To This Post Posted: April-09-2008 at 10:49pm
ripsaw describe it to me over the phone
"the things you own will start to own you"
Back to Top
 Post Reply Post Reply
  Share Topic   

Forum Jump Forum Permissions View Drop Down

Copyright 2024 | Bagley Productions, LLC